Announcement

Collapse
No announcement yet.

Planning my 32" cast oven

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • #16
    Sidetrack , I saw your comment on creating a sectional dome in Kris S's build threat. Didn't want to hijack that thread. The idea is intriguing.
    I am planning for my own cast build. Base is complete. I have a few weeks wehre I won't be able to make much progress other than planning the final details.

    Here are some thoughts:
    • make three sections, and a top part, would have to make sure that the top (plug) is tapered so that it does not fall through
    • Maybe use thin cardboard to keep the seams thin
    • Maybe fold the cardboard into a wedge shape I don't think I could do the nice bullnose that you have drawn, but maybe a triangular shape
    • Or maybe even simpler, make a step in the homebrew 1" wide (see attached sketch)
    • would also have to place something between the firebrick and the dome (cardboard?)
    • Let the Homebrew cure for 48 hrs, remove the sand, fix any imperfections on the inside, let wet cure for at least another 5 days
    Now comes the interesting part.
    • Once everything is cured, I would have to take the dome apart so that it can be put together again using high temp mortar.
    • Or simply burn out the thin cardboard and let it settle?
    Not sure if it is worth the effort. I am going to use burnout fibers as well as Stainless Steel needles for structure.

    Any thoughts are welcome.
    My oven build thread https://community.fornobravo.com/for...y-32-cast-oven

    Comment


    • #17
      OK, another question as I am going to pick up my firebrick tomorrow.
      Looks like I can conveniently use a whole brick for the gallery portion.
      After that I have seen two layouts on this site:
      1. cut a triangular piece of the first set of bricks and butt them up against the bricks in the gallery (left in the drawing attached)
      2. use a small triangular piece to start with (right in the attached drawing)
      Both layouts seem to take 31 bricks (plus a few to break just in case) to make the floor
      I am tending towards option 1, might provide a cleaner and more stable entrance, but does it really matter?

      Any suggestions?
      My oven build thread https://community.fornobravo.com/for...y-32-cast-oven

      Comment


      • #18
        It doesn’t really matter. The ragged edge of the floor bricks can be trimmed a little, but the insulation will cover it anyway. That is one of the big advantages of building the dome on top of the floor rather than the dome being outside the floor, which requires more precise floor brick cutting.
        Kindled with zeal and fired with passion.

        Comment


        • #19
          David, yes, I understand that part. I was more wondering about the pattern from the gallery entrance bricks to the herringbone part. I guess it does not really matter.
          My oven build thread https://community.fornobravo.com/for...y-32-cast-oven

          Comment


          • #20
            Toward the end of this post ,.......JRPizza explains how and the why in which he laid the entry/galleryfloor brick.
            Last edited by Gulf; 10-03-2021, 08:06 PM.
            Joe Watson " A year from now, you will wish that you had started today" My Build Album / My Build

            Comment


            • #21
              Gulf , thanks for pointing me to that post. Yes, i am planning on doing the straight in bricks for the gallery. I am just wondering how to continue from there with the herringbone pattern. Two options as i has drawn 3 or so posts up.
              One has small triangular pieces, then a complete brick.
              The other has a triangular pice cut from the first "row" of bricks.
              I have seen both and was wondering if there is a preference. I am sure both will work, but was just wondering if there is a preferred way to lay these bricks
              My oven build thread https://community.fornobravo.com/for...y-32-cast-oven

              Comment


              • #22
                Both will work. You’re call. However, neither pic is an actual herringbone pattern. But, the diagonal lay serves the same purpose.
                Joe Watson " A year from now, you will wish that you had started today" My Build Album / My Build

                Comment


                • #23
                  Gulf , Of course, you are absolutely correct, not sure how what i was thinking.

                  I updated the layout (more so that I know how many bricks to buy).

                  If I counted correctly the left layout requires one less brick (31 bricks, not that it matters) vs. the one on the right, because I can cheat a bit using a cutoff for the bottom left most brick technically not quite in the pattern.

                  I still think I will go with the one to the right. I kind of like the look at the entrance a bit better I think.

                  My oven build thread https://community.fornobravo.com/for...y-32-cast-oven

                  Comment


                  • #24
                    I did something like what you are showing on the right, where the bricks closest to the entrance were full length along one side and only a small wedge was cut off. Not sure it matters but not having small wedges right at the transition seemed to be more stable.
                    My build thread
                    https://community.fornobravo.com/for...h-corner-build

                    Comment


                    • #25
                      Thanks JR, that's what I was thinking as well. I think that's the way I will go

                      BTW, Love your build thread, very detailed
                      My oven build thread https://community.fornobravo.com/for...y-32-cast-oven

                      Comment


                      • #26
                        The arch appears to not be centered. The top side is over farther than the bottom side. FYI, the inner arch needs to intersect the ID of the dome at the first course.
                        Russell
                        Google Photo Album [https://photos.google.com/share/AF1Q...JneXVXc3hVNHd3/]

                        Comment


                        • #27
                          UtahBeehiver , not sure what you are referring to. The left most (straight) bricks are the floor for the gallery. I should center them so that it looks symmetrical but would then have to cut two bricks instead of one.
                          I am doing a cast dome, so there is no arch other than the decorative arch.
                          Sorry if I misunderstood. I certainly appreciate any feedback.

                          I have attached an updated drawing. Any comments?
                          My oven build thread https://community.fornobravo.com/for...y-32-cast-oven

                          Comment


                          • #28
                            I will of course cut the bricks to a shape closer to the cast dome than shown on the drawing
                            My oven build thread https://community.fornobravo.com/for...y-32-cast-oven

                            Comment


                            • #29
                              I see, those entry floor bricks look like they were arch bricks.
                              Russell
                              Google Photo Album [https://photos.google.com/share/AF1Q...JneXVXc3hVNHd3/]

                              Comment


                              • #30
                                No problem, I am super happy with all the feedback I have received here. It will hopefully keep me from making too many mistakes and will result in a better oven.
                                My oven build thread https://community.fornobravo.com/for...y-32-cast-oven

                                Comment

                                Working...
                                X