Announcement

Collapse
No announcement yet.

Mongo's 42" CT Build

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • GianniFocaccia
    replied
    Re: Mongo's 42" CT Build

    So, here's my minivan. A 2002 Honda with about 200K miles on it, and I wouldn't be surprised if it's carried 200K pounds of construction stuff in the back of it over the years
    Aren't Odyssey's great? My 2000 has over 230k miles on it, and is the preferred hauler over my F-250 (10 mi/gal) as long as whatever I'm moving fits inside without too much trouble.

    I feel for your poor back after loading/unloading those CMU's.

    Leave a comment:


  • mongota
    replied
    Re: Mongo's 42" CT Build

    Tony, thanks.

    Well, it's the end of Day Five.

    Managed to get the last two courses of CMU mortared in.



    I've seen a lot of guys dry stack their block and use angle iron for the over-door support.

    I'm planning to pour a lintel and reinforce it with rebar. I'll cut into the ends of the two top blocks on each side of the door to open those block cells up, that'll help tie the lintel pour over the door in with the block wall.

    I was contemplating making the lintel integral with the cap slab pour. But that depends on if I can form it up neatly, and more importantly, if I can bear to add another 7 bag count for the lintels to the 35-bag pour for the slab. I'll probably do them separately.

    Anyhow, with Day Five done, the hearth will sit idle for a few days. Rain is expected and I have a few indoor projects to do.

    I appreciate the encouragement over the past few days. Thanks, kids!

    Leave a comment:


  • Tonyp
    replied
    Re: Mongo's 42" CT Build

    Looking great Mongo! You do some very nice work. Not to mention you are so much faster than I am.. it takes me about 5 minutes to set one brick LOL. Definitely worth spending a bit of extra time initially to make sure things are level, square, plumb and lined up exactly where you want them.

    Leave a comment:


  • mongota
    replied
    Re: Mongo's 42" CT Build

    A bit of a surprise today. I was supposed to be out of town all day but ended up home by late afternoon. What to do, what to do...

    I know! I'll turn the mini-van into a pick-up truck! I'll post this in honor of a buddy of mine who was giving me grief. He has a Ford F250 with a bed liner, and he's never carried anything in the back out of fear of scratching the bed liner.

    So, here's my minivan. A 2002 Honda with about 200K miles on it, and I wouldn't be surprised if it's carried 200K pounds of construction stuff in the back of it over the years. Stuff like this:



    36 CMU, eight 2x4s, and 12 pieces of rebar.

    Went shopping, got home, and got to work. The layout took way too long, but I wanted to get the blocks properly located on the slab and the walls square. Only had a few hours before dark, but I was able to get two courses of CMU plus a start on the third course mortared in place.



    There was a darkness on the edge of town...

    Leave a comment:


  • SteelandStone
    replied
    Re: Mongo's 42" CT Build

    It is coming along nicely, I would have had to have two of those beers after hand mixing all those bags. I used to do it by hand too but a mixer sure spoils you.

    Leave a comment:


  • mongota
    replied
    Re: Mongo's 42" CT Build

    Originally posted by kbartman View Post
    Mongo,
    Below is a some info I pulled off the internet...
    I appreciate that, thanks.

    Leave a comment:


  • mongota
    replied
    Re: Mongo's 42" CT Build

    Originally posted by Gulf View Post
    Monago,
    "What they said" .

    I see a marked discoloration in the top inch or so of your slab. Is that an acrylic that you applied before or after wrecking the forms?
    I think you're just seeing a 45-degree chamfer I added to the top outside corner of the slab.

    Here's a close-up of a corner, it might help clarify things:

    Last edited by mongota; 08-03-2018, 07:51 PM.

    Leave a comment:


  • kbartman
    replied
    Re: Mongo's 42" CT Build

    Originally posted by mongota View Post
    Thanks for the kind words.

    I have an old Red Lion mixer that I bought years ago, but it's on the fritz. That mixer has a roughly 8" long axle that threads into the back of the mixing barrel. Even with proper greasing, that axle is simply worn out, so there's a bit of wobble in the barrel as it rotates, causing the cogs on the perimeter of the mixing barrel to intermittently miss the gears of the drive motor.


    THAT will be a pain. You'll probably see more than one celebratory beer being consumed when that slab is done. lol
    Mongo,
    Below is a some info I pulled off the internet. I believe this is the guy I called to get parts to repair my mixer. I believe they are the same mixers. He only had a few left at the time, and at a very good price. The manufacture longer no sells these parts. Give him a call its worth a shot.


    Monarch Cement Mixers & Repair Parts - Ken's Distributing . .... Monarch industries red lion type b cement mixer parts ... To get all parts for th Big Cat cement Mixer By Redlion; here is the phone number: 1-800-575-1935, Ken's ...

    Leave a comment:


  • GianniFocaccia
    replied
    Re: Mongo's 42" CT Build

    With the top of the slab forms being about 36" above the ground I'll have to transfer the mix from the wheelbarrow to drywall buckets then hand-dump them into the form
    Thats how I poured my support slab (9.5" deep along the perimeter), and yes, there was a celebratory sixer after that little project.

    Leave a comment:


  • Gulf
    replied
    Re: Mongo's 42" CT Build

    Monago,
    "What they said" .

    I see a marked discoloration in the top inch or so of your slab. Is that an acrylic that you applied before or after wrecking the forms?
    Last edited by Gulf; 10-05-2014, 10:12 AM.

    Leave a comment:


  • mongota
    replied
    Re: Mongo's 42" CT Build

    Thanks for the kind words.

    I have an old Red Lion mixer that I bought years ago, but it's on the fritz. That mixer has a roughly 8" long axle that threads into the back of the mixing barrel. Even with proper greasing, that axle is simply worn out, so there's a bit of wobble in the barrel as it rotates, causing the cogs on the perimeter of the mixing barrel to intermittently miss the gears of the drive motor.

    For this oven project, it's all hand-mixing. It moves at a pretty good pace with my wheelbarrow and a masons hoe. I get into a pretty good rhythm when mixing by hand.

    The mix that will be a pain will be when forming up the slab going on top of the hearth. It'll probably be a 35 bag pour, with maybe one-fourth of the bags being pigmented for integral slab color. With the top of the slab forms being about 36" above the ground I'll have to transfer the mix from the wheelbarrow to drywall buckets then hand-dump them into the form.

    THAT will be a pain. You'll probably see more than one celebratory beer being consumed when that slab is done. lol

    Leave a comment:


  • kbartman
    replied
    Re: Mongo's 42" CT Build

    Originally posted by UtahBeehiver View Post
    Great start, you mixing all that concrete by hand just saw a wheelbarrow sitting in the back ground.
    Wow !!! Impressive pool setting. The Oven design will definitely complement all. Look forward to following you build.

    It's a shame your not a lot closer I have a cement mixer I picked up off of Craig's list that will be going back on the market soon. Surely you didn't hand mix all that Quik-crete If you did, I would not want to get in any tussle with you

    Good Luck,
    Last edited by kbartman; 10-05-2014, 09:45 AM.

    Leave a comment:


  • UtahBeehiver
    replied
    Re: Mongo's 42" CT Build

    Great start, you mixing all that concrete by hand just saw a wheelbarrow sitting in the back ground.

    Leave a comment:


  • mongota
    replied
    Re: Mongo's 42" CT Build

    The slab. I let it sit until it was pretty well set, then hit it hard with the trowel. It's about as flat as I could have gotten it and I'm happy with the finish. This is after misting it the next day:

    Last edited by mongota; 10-04-2014, 08:33 PM.

    Leave a comment:


  • mongota
    replied
    Re: Mongo's 42" CT Build

    I used 12" blocks for the two courses of mortared CMU that would end up below grade.



    With the two courses mortared in, I compacted backfill inside and out, then tied off the rebar.



    And yup...more Quikrete...22 bags worth.



    Followed by a beverage of my choice:

    Leave a comment:

Working...
X