Announcement

Collapse
No announcement yet.

Dave's Pics of Progress

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • asudavew
    replied
    Re: Dave's Pics of Progress

    And of course my daughter Harley helping as usual!


    She is always willing to lend me a hand!

    Leave a comment:


  • asudavew
    replied
    Re: Dave's Pics of Progress

    No hearth this weekend. It was too hot in my neck of the woods.


    But I did get a good start on the forms.

    Here's a few pics.


    I wanted a overhang all around the stand so I built my forms 1 1/2 bigger on the back and the sides. The front will have a 12" cantilever.

    I started the forms upside down to make the screwing easier, then flipped it right side up, placed it around the stand and put support legs under it.

    I will post a picture of the final form when I complete it.

    I almost forgot... I didn't level the initial blocks on the pad, so I am leveling the hearth pour to make it all work out. Actually I will probably have the mouth of the oven slightly lower than the back of the oven. So water can't get in the oven.

    Leave a comment:


  • asudavew
    replied
    Re: Dave's Pics of Progress

    Well..... call me crazy, but I picked up a load of sand/gravel mix today.

    Tomorrow I will pick up some cement and my form materials..... Hopefully by the time the weekend is over I will have a hearth!

    Leave a comment:


  • asudavew
    replied
    Re: Dave's Pics of Progress

    Originally posted by Kemo View Post
    Dave,

    Greetings from Austin! Hook'em!

    Nice to see another TEXAS oven. I hope to start mine here in the next month.
    Thanks for posting.
    Thanks Kemo,

    and Go Cowboys!

    Leave a comment:


  • asudavew
    replied
    Re: Dave's Pics of Progress

    I posted some info on using lava rock as an insulator.

    http://www.fornobravo.com/forum/f8/lava-2487.html

    Leave a comment:


  • Kemo
    replied
    Re: Dave's Pics of Progress

    Dave,

    Greetings from Austin! Hook'em!

    Nice to see another TEXAS oven. I hope to start mine here in the next month.
    Thanks for posting.

    Leave a comment:


  • asudavew
    replied
    Re: Dave's Pics of Progress

    Thanks Mark.

    They are pretty ugly now, but a good outer coat and hopefully it will be as pretty as the pizzas I will cook!

    Leave a comment:


  • maver
    replied
    Re: Dave's Pics of Progress

    So you are using reclaimed concrete block? I recently had to demolish the oven stand from my old house after moving (and moving the oven). I wanted to find a better disposal for all the concrete block and concrete rubble than just a landfill and found a sand/gravel dealer that accepts concrete for reuse (they took my whole stand for $15, way cheaper than the landfill and I feel better it will be reused). I was amazed looking at the massive (mostly commercial) pile of rubble they had and the possible uses. There were plenty of pieces that could have been used as part of an oven stand as well as what must have been someone's fireplace bricks that looked low duty. I didn't ask what they charge to cull through that, but the reused concrete market looks like a good source for low cost materials for an oven (plus, with recycling you could bill it as a 'green' oven).

    Anyhow, nice work.

    Marc

    Leave a comment:


  • asudavew
    replied
    Re: Dave's Pics of Progress

    Just a few more of filling cells.

    I will post a picture of the completed stand tomorrow.

    I thought I had a good shot of it, but I don't.

    The angle iron that can be seen, isn't really angle iron.
    I had and old garage door opener that the previous owner left at my house.
    It had an 8 foot section of a T-shaped piece of 3/16ths iron.
    So I cut it up. I think the T shape will be stronger than angle iron.
    And it saved me a trip to the dump, and it saved me some dough!
    Last edited by asudavew; 08-28-2007, 06:38 AM. Reason: Additional information.

    Leave a comment:


  • asudavew
    replied
    Re: Dave's Pics of Progress

    A busted knuckle.

    Concrete dust.

    And the best helper a dad could ever hope for, my 16 year old son!

    Leave a comment:


  • asudavew
    replied
    Re: Dave's Pics of Progress

    This is a shot of me and my tape measure.

    Love those Stanley tapes with the wide blade and curved housing.


    There is also two closeups of the different tiles I have.

    I have 176 of the plain ones and 58-59 or so of the one with the treads.

    BTW It was hot here in West Texas and humid. Somewhere near 100 F.
    And sitting at a desk for the last year hasn't helped. I'm not used to it anymore!
    Last edited by asudavew; 10-10-2007, 09:59 AM.

    Leave a comment:


  • asudavew
    replied
    Re: Dave's Pics of Progress

    My temporary stack.

    Leave a comment:


  • asudavew
    replied
    Re: Dave's Pics of Progress

    Knocking off old mortar.

    Leave a comment:


  • asudavew
    started a topic Dave's Pics of Progress

    Dave's Pics of Progress

    Here are some pictures of the used blocks I acquired.
    I had to knock some mortar off, but none the less, they worked fine.

    Then several pics of my son and I putting it all together and filling the cells.


    We have LIFTOFF!

    I also got some "new tiles" that were left over from a Pizza Hut remodel my father and I did over 10 years ago. They were supposed to be used for the floor, but we had purchased a few too many boxes. Somehow I will incorporate them into my design. (I just realized these were intended to be used in a "Pizzeria," so they finally will get their day! Although I am sure it won't be hard to make better pizza than the hut)

    These first pics are the used blocks in my Excursion.
    Last edited by asudavew; 10-03-2007, 09:49 AM. Reason: New title
Working...
X