Well the time has arrived . I have been doing slab work and cinder block support structure , perlcrete hearth , stuff like that and asking lots of questions and reading all the build threads I can . Yesterday I laid down the hearth bricks and put up 4 courses to form the box of the oven . Today I am starting the dome . I have dry stacked it ( first row ) to make sure the form is correct and things do what they are supposed to . I think I am going to just leave it dry stacked and push the mortar down in the joints with a trowel . My adventure has begun !!! thanks everybody for all the input and answers so far , I am sure there will be plenty more.
Starting my barrel vault
Collapse
X
-
Tags: None
-
Re: Starting my barrel vault
Post some pics!Ken H. - Kentucky
42" Pompeii
Pompeii Oven Construction Video Updated!
Oven Thread ... Enclosure Thread
Cost Spreadsheet ... Picasa Web Album -
Re: Starting my barrel vault
Well I got 3 rows of the dome done today . I have to start on the transition now although I am not 100 % sure yet what to do . time to read some more . One thing that came to mind that I never thought of while looking at the different builds was the dome mortar . After actually doing it I am wondering if the mortar acts more like a glue , or more like a spacer , holding the bricks apart so that they can not fall in on themslves. I did take some pics as i went . I will try to figure out how to post them .My Oven Build
http://www.fornobravo.com/forum/f6/s...ult-18532.htmlComment
-
Re: Starting my barrel vault
Al , I see on your build that you put the flue right in the tpo of the dome . I have not seen this approach on any other oven . Do you like the way it works? would you do it again? It appears that it might take a bit more fire to get up to temps , yes?My Oven Build
http://www.fornobravo.com/forum/f6/s...ult-18532.htmlComment
-
Re: Starting my barrel vault
I love the way it works and it draws beautifully with no smoke out the front unless I put the damper in too far.
Pizza temps in 2 hours, roast temp in 1 hour.
Comment
-
Re: Starting my barrel vault
here is my try at posting pics , hope it works . If it is wrong , mods please feel free to remove them . As you can see its just a standard build , nothing earth shattering .4 PhotosMy Oven Build
http://www.fornobravo.com/forum/f6/s...ult-18532.htmlComment
-
Re: Starting my barrel vault
here are a couple more . First one is the dry run to see if things lined up close and the second is putting it to bed for the evening . I covered it with the plastic , then a tarp and turned the light on for more heat . Kept it nice and toasty all night long .Some of the pics I took wont load but you get the idea . comments and critisizms welcome2 PhotosMy Oven Build
http://www.fornobravo.com/forum/f6/s...ult-18532.htmlComment
-
Re: Starting my barrel vault
Nice work keep going, you might want to toss a piece of plywood or cardboard on the floor to make it easier to keep things clean. But you are doing a great job or that nice clean install and nice tight joints.here are a couple more . First one is the dry run to see if things lined up close and the second is putting it to bed for the evening . I covered it with the plastic , then a tarp and turned the light on for more heat . Kept it nice and toasty all night long .Some of the pics I took wont load but you get the idea . comments and critisizms welcome
The photos might not load because they are to large try lowering the quality/resolution of the photos that you use for uploading.
ChipChipComment
-
Re: Starting my barrel vault
You should use running bond on the brick of the cieling, i.e. start every other row with a half, but other than that, it looks like a nice oven with a lot of mass.Comment
-
Re: Starting my barrel vault
Is there any reason not to build your chimney just out of brick? I am having trouble locating a usable masonry flue liner and can not figure out how to adapt a steel double wall flue pipe to the top of the brick so I thought I might just build the brick chimney and call it good . Any reason I shouldnt go this route? Thanks.My Oven Build
http://www.fornobravo.com/forum/f6/s...ult-18532.htmlComment
-
Comment
-
Re: Starting my barrel vault
Can perlcrete be used as a suitable thermal break or will it crush and stay that way after the first full firing? Thanks.My Oven Build
http://www.fornobravo.com/forum/f6/s...ult-18532.htmlComment
-
Re: Starting my barrel vault
You can see the space where it would go in these pics . The middle pic is probably the clearest shot of where the gap is .3 PhotosMy Oven Build
http://www.fornobravo.com/forum/f6/s...ult-18532.htmlComment





Comment