Gauge of lintels in block stand?

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • dbhansen
    Master Builder
    • Jun 2007
    • 566

    #1

    Gauge of lintels in block stand?

    I was checking out the angle iron at the local Big Box Store and found that they carry varying widths and thicknesses. I specifically recall that they had some at about 1.25" wide @ 1/8" gauge and about 2" wide @ 3/16" gauge. Would those both be wide and strong enough? What's the recommended minimum gauge for the lintels?
    Picasa web album
    Oven-building thread
  • dmun
    Il Pizzaiolo
    • Jul 2005
    • 4218

    #2
    Re: Gauge of lintels in block stand?

    I think the thicker/bigger angle iron is indicated. Don't hesitate to visit your local junkyard/scrap metal dealer. They may have even bigger pieces, and will cut it to length for you. I think the stuff at HD is overpriced.
    My geodesic oven project: part 1, part 2

    Comment

    • christo
      Master Builder
      • Feb 2006
      • 913

      #3
      Re: Gauge of lintels in block stand?

      If I had it to do over again - and I likely will someday....

      I would forgo the lintels all together - and let the slab span the opening in the front. There are many examples of this alternative here.

      Christo
      My oven progress -
      http://www.fornobravo.com/forum/f8/c...cina-1227.html
      sigpic

      Comment

      • dmun
        Il Pizzaiolo
        • Jul 2005
        • 4218

        #4
        Re: Gauge of lintels in block stand?

        Here's a clever idea from JED:



        Cutting out sections of block divider, and inserting rebar for a reinforced lintel. Of course you have to support the span from below when you set it up, and fill it with concrete. A slightly more expensive idea is to buy a pre-cast concrete lintel to span the gap. You could do like I did, and make a form and build a masonry arch.

        Or as christo says, you could just put an extra piece of rebar in the front of the slab, and forgo the lintel entirely.
        My geodesic oven project: part 1, part 2

        Comment

        • asudavew
          Il Pizzaiolo
          • Jul 2007
          • 1880

          #5
          Re: Gauge of lintels in block stand?

          I love the idea of forgoing the lintel.
          But I used one.
          Just an old t-shaped bar from a garage door opener that the previous owner left at my house.
          It worked fine and the t-shape adds some strength.
          My thread:
          http://www.fornobravo.com/forum/f8/d...ress-2476.html
          My costs:
          http://spreadsheets.google.com/pub?k...Xr0fvgxuh4s7Hw
          My pics:
          http://picasaweb.google.com/dawatsonator

          Comment

          • dbhansen
            Master Builder
            • Jun 2007
            • 566

            #6
            Re: Gauge of lintels in block stand?

            Thanks for the input! I'm considering a cantilevered hearth and a brick arch in the opening to the wood storage area (kinda like my avatar shows, and like Ken has done), so I think I need the blocks to span the opening. But I will investigate these ideas further and try to find pictures of other methods. Thanks again.
            Picasa web album
            Oven-building thread

            Comment

            • Dutchoven
              Master Builder
              • Apr 2007
              • 931

              #7
              Re: Gauge of lintels in block stand?

              You could build the arches first and then pour the slab...
              Just a thought!
              Dutch
              "Making the simple complicated is commonplace; making the complicated simple, awesomely simple, that's creativity. " Charles Mingus
              "Build at least two brick ovens...one to make all the mistakes on and the other to be just like you dreamed of!" Dutch

              Comment

              • brokencookie
                Journeyman
                • Oct 2007
                • 376

                #8
                Re: Gauge of lintels in block stand?

                Originally posted by Dutchoven
                You could build the arches first and then pour the slab...
                Just a thought!
                Dutch
                You must be reading my mind. My plan is to do exactly that. Hopefully I will get the arch right. But if I don't, I can tear it down and redo it up until the slab is poured. The arch should provide a lot more bearing strenght than a straight lintel
                Sharpei Diem.....Seize the wrinkle dog

                Comment

                • dbhansen
                  Master Builder
                  • Jun 2007
                  • 566

                  #9
                  Re: Gauge of lintels in block stand?

                  Now that's an interesting idea. The arch itself could help support the hearth slab. I like it!
                  Picasa web album
                  Oven-building thread

                  Comment

                  • dbhansen
                    Master Builder
                    • Jun 2007
                    • 566

                    #10
                    Re: Gauge of lintels in block stand?

                    I just came across this document on brick arches:

                    Brick Masonry Arches

                    It has lots of images to get the brain juices flowing!
                    Picasa web album
                    Oven-building thread

                    Comment

                    • Dutchoven
                      Master Builder
                      • Apr 2007
                      • 931

                      #11
                      Re: Gauge of lintels in block stand?

                      If you send me the span measurement, your brick size and the size of the mortar joint your shooting for, I can calculate the number of bricks and even tell calculate a taper for you if you want to do any cutting
                      Best
                      Dutch
                      "Making the simple complicated is commonplace; making the complicated simple, awesomely simple, that's creativity. " Charles Mingus
                      "Build at least two brick ovens...one to make all the mistakes on and the other to be just like you dreamed of!" Dutch

                      Comment

                      • dmun
                        Il Pizzaiolo
                        • Jul 2005
                        • 4218

                        #12
                        Re: Gauge of lintels in block stand?

                        What a good resource! Who knew that every row of bricks above an arch needed an individual flashing?
                        My geodesic oven project: part 1, part 2

                        Comment

                        • dbhansen
                          Master Builder
                          • Jun 2007
                          • 566

                          #13
                          Re: Gauge of lintels in block stand?

                          Originally posted by Dutchoven
                          If you send me the span measurement, your brick size and the size of the mortar joint your shooting for, I can calculate the number of bricks and even tell calculate a taper for you if you want to do any cutting
                          Best
                          Dutch
                          Thanks Dutch!! I'll keep that in mind and let you know.

                          Daren
                          Picasa web album
                          Oven-building thread

                          Comment

                          Working...