Hearth Floor

Collapse
X
 
  • Time
  • Show
Clear All
new posts

  • MK1
    replied
    Re: Hearth Floor

    So, let me see if I have this right. We place the item (pizza or bread) on the floor. The bottom of the item gets most of it's heat from conduction, the top from convection and radiation. While cooking the floor is giving up heat and cannot recharge because it's shaded by the item. When removed, the thinner floor recharges quickly. So it's a fast floor.
    A floor with greater mass after heating up would have greater heat reserves, not need to recharge as soon, but would then take longer to recharge, so it's a slow floor.
    If I'm understanding this thing right, sizing the components based on their conductivity and heat retention capabilities is a bit of a trick. An oven with greater mass might heat up quicker with a more conductive material, behave more like a lower mass oven but would require more insulation. I might be way off base here, and I'm not sure what compromises material properties would impose.
    I see some builders use the "island hearth" with a layer of splits added to the floor but I don't think I saw more insulation specified. If my thinking is correct, this gives greater heat reserves but slows the floor down. I would be very interested to know how the 3" island hearth performs.

    Mark

    Leave a comment:


  • dmun
    replied
    Re: Hearth Floor

    The 2 1/4 inch floor developed through trial and error. The early builders thought that the oven should have additional mass on the floor, and the original plans called for the insulation layer to be below the support slab. This was not a success, with long heat-up times and the floor too cool for pizza cooking. Then there was experimentation with an "island hearth", with a slug of concrete thermal mass just below the cooking floor. Finally it was determined that just the single layer of firebricks did the job fine, directly on top of the insulation.

    So, in retrospect, why does the oven have so much more mass on top of the oven than on the floor? The simple answer is that heat rises. The oven gets MUCH more hot on top than on the bottom, to the point where the WFO can work like the broiler in a gas stove, using the heat radiating down from the top. A thick floor is a cool floor, and a thinner floor will more easily get and keep pizza heat.

    Leave a comment:


  • Les
    replied
    Re: Hearth Floor

    Originally posted by MK1
    You stated that you're using your oven more for baking. Is it just the floor that needs additional mass or the whole oven?
    I think the whole oven if your goal is baking. The Allen Scott design is all about mass and it's for baking. I don't think you will go wrong with adding more to the floor - it will require more fuel and time to get to temp. This design lets the dome reflect the heat back down to re-charge the floor. I have heard of some, that while cooking a lot of pizza's, move the coals over the spot to speed up the process. If I were to do it over, I think I would put them on edge - you will end up with more edges, but it time it will smooth out. Be interesting to see what others think about this.

    Keep having fun!

    Les...

    Leave a comment:


  • MK1
    replied
    Re: Hearth Floor

    Les,

    My question concerns the thickness of the floor vs the dome. I know from reading a lot on this forum that this design is very well thought out and enough have been built and tested to refine and prove them. I think I understand why most of the features and details are established but I wonder why the floor can be less thermal mass than the dome.
    Is it because the fire and coals conduct directly, heating the floor to a higher temperature? Would a 3" or 4" thick floor burn the bottom before the top is done? I assume there's some kind of thermal release from the floor to the pizza or bread because direct contact and might suppose that a 2" floor has just the right amount of retained heat.
    You stated that you're using your oven more for baking. Is it just the floor that needs additional mass or the whole oven?
    I have started on my supports for the slab, who ha! Materials are converging on my unworthy domicile at this very moment. I'm excited. Damn, I love a project!

    Mark

    Leave a comment:


  • Les
    replied
    Re: Hearth Floor

    Mark, if you lay them on edge you are adding mass. That may not be a bad thing. In hind sight (as I am trying to cook coconut shrimp) I would consider a longer heat up time for more retained heat. Baking is becoming the best feature of my oven - we are getting burned out on pizza (you guy's don't know where I live so put out the torches ) My reason for laying them flat - it was in the plans...
    Les...
    Last edited by Les; 04-13-2009, 01:46 PM.

    Leave a comment:


  • DrakeRemoray
    replied
    Re: Hearth Floor

    Most lay them flat so the floor will stay nice and hot during pizza making.

    Leave a comment:


  • ThisOldGarageNJ
    started a topic Hearth Floor

    Hearth Floor

    Hello All,,
    I poured my vermiculite slab today and hope to start the actual oven next week... I was wondering how many people lay their hearth bricks flat and how many stand them on edge and if you have your reasons for doing so ?

    Thanks
    Mark
    TOGNJ
Working...