Hearth Floor

Collapse
X
 
  • Time
  • Show
Clear All
new posts

  • jbergen
    replied
    Re: Hearth Floor

    Thanks, Steve. Great pics, BTW.

    Leave a comment:


  • Greenman
    replied
    Re: Hearth Floor

    The bottom line really is how much of what you are going to use if for. If you have the hearth isolated by insulation then the basic plans are quite efficient enough to cope with normal domestic requirements.

    Mine is an 'igloo' built on 4" of vermicrete, the bricks of the hearth laid on the flat and the dome built with half bricks then insulated with ceramic fibre and then more vermicrete before the render layer.

    It heats up in an hour and a half and maintains useful heat for a couple of days after which it takes little to bring it back up to temp.

    I think that the trap can be to over-think the whole process. Lots of good builds to draw ideas from here but most of them are built to the FB plan or with minor variations from it.

    Good luck with it.

    Leave a comment:


  • jbergen
    replied
    Re: Hearth Floor

    You might find part of your answer over in another thread
    http://www.fornobravo.com/forum/f2/n...rta-21667.html

    Leave a comment:


  • Brodek
    replied
    Re: Hearth Floor

    jBergen,

    In the same boat, so they say. Want to build my oven for bread first, and pizza as a nice Friday night side...with a target of Saturday morning baking. Only one or two bakes, because how much bread do we need?

    I originally was convinced (by self) that the Allen Scott oven was best...but after a LOT of reading/research I may have been pursuing too much "mass", rendering the firing/heating into a too-long process. Again, I'm not going to bake all day, but I would like enough mass to handle baking the morning after a pizza event.

    My current thinking and questioning is whether I should add ceramic fiber board over my 4" vermiculite layer (Econolite) and use the fire bricks on their sides for my floor mass. Or, should I lay the floor directly on the vermiculite layer and lay them flat or on their sides? I haven't been able to really find exactly the answer... And, I won't even get into the "should I change to an igloo shape"... thought-track.

    Never expected this to be easy...but thought I could make a decision!

    Will be following this thread closely to see what ideas emerge.

    Kevin

    Leave a comment:


  • jbergen
    replied
    Re: Hearth Floor

    I've been researching the "island hearth" comments on the forum, and I wonder if what I'm reading from 2009 or so is the final & best answer. We're building the oven with an interest in baking bread. Has it been determined that the 2" floor tiles supplied in the FB kit are adequate, or should I still consider adding 1 1/4" splits under that floor? (and then the rigid ceramic insulation under that)

    Leave a comment:


  • MK1
    replied
    Re: Hearth Floor

    Okay now I get it. I took a closer look at the graphic above and included in the plans. It clearly states that it's showing how the heat moves to the outer edge of the mass. I had read that but didn't have enough background to understand. It takes me a little while. Again I appreciate all the prototyping you've done, and I can't wait to fire it up.. that is, after I finish building it.

    Mark

    Leave a comment:


  • james
    replied
    Re: Hearth Floor

    Originally posted by MK1
    I'm assuming that when James says we're not filling the floors as it is, the dome is 1000F near the end of firing, the floor is somewhere below that (800?) and as the initial "plasma" phase dies out the respective temps equalize.
    Mark
    Mark, that's not quite it. Typically you can fire the dome and floor to roughly the same temperature.

    Think if the floor (or dome for that matter) as having both inner and outer facing edges. When the inside of your oven is hot, let's say 800?F on both the dome and the floor using an infrared thermometer, you are measuring the inner face. The part facing the fire. At that point, the outer face will be much cooler, depending on how quickly you fired up your oven. From that point on, you can continue firing your oven, and the inner face will stay roughly 800?F, and the additional heat will continue to drive up the temperature of the outer face of your dome and floor. That's the stored heat you use when you bake without the fire.

    Alternatively, when the inner face of your oven is hot and the outer face is still cold -- and you take out the fire -- the two faces of your oven will meet in the middle to the point of equilibrium, and the entire mass will become only moderately warm. The inner face will cool down and the outer face will wick heat outward.

    That's what I meant by "filling" your oven with heat. I tried to capture that with our FB heat graphic.
    James

    Leave a comment:


  • dmun
    replied
    Re: Hearth Floor

    I know I'm being a PIA but I am compelled to turn this thing over in my mind until I think I understand the thermal dynamics of the oven,
    Not at all. We would a LOT rather have people ask questions before they build, rather than after.
    always trying to reinvent the wheel.
    I'm in no position to criticize any one for that.

    Leave a comment:


  • MK1
    replied
    Re: Hearth Floor

    Thanks to all for the replies. I have a clearer picture of what's happening in the oven. The thread Drake refers to is somewhat telling in that each quadrant has a slightly different temp, particularly the fire quadrant.
    I'm assuming that when James says we're not filling the floors as it is, the dome is 1000F near the end of firing, the floor is somewhere below that (800?) and as the initial "plasma" phase dies out the respective temps equalize.
    I have my four piers done and in the next few days I'll pour the slab. I'm going to insert an .015 X 3" stainless flashing edgewise into the concrete (vertically) that will describe the outer perimeter of the insulation and be inside the final render (igloo design) I'll soon post a few pictures as there is more to look at. I will also mention that I've looked at almost all the builds on this forum and you SOBs have set the bar pretty high!

    Mark

    Leave a comment:


  • DrakeRemoray
    replied
    Re: Hearth Floor

    MK1,

    Check out this thread.
    http://www.fornobravo.com/forum/f17/...temp-6528.html
    It discusses the problem of burned bottoms on bread. I think a cooler floor is acutally a benefit when baking. I do a lot of baking (see this thread) - and have had more problems with burnt bread bottoms than anything else. I think of the dome as the battery that charges the oven. A little extra mass in the dome (I added 1inch of mortar) may help, but others without that extra mass have reported very similar oven temps over time. I think the real key is insulation.

    Hope that helps,
    Drake

    Leave a comment:


  • james
    replied
    Re: Hearth Floor

    Hi Les,

    They will definitely eventually get saturated, but I think it's at a much hotter and longer burn than we are typically doing when we either bake pizza or fire our ovens for baking. I used the term "never" too liberally -- but my point is that we aren't "filling" the floors that we have. I have never even fully fired a Primavera -- which holds a huge amount of heat.

    In terms of floor mass, we've seen it all:

    9" Scott oven -- bricks on side, set on 4 1/2" concrete slab
    5" 2" Casa floor set on 3" firebrick island
    4 1/2" bricks on side
    2 1/2" - 3" firebrick floor
    2 3/4" Modena commercial oven floor
    2" precast residential floor
    1 1/2" firebrick split floor

    James

    Leave a comment:


  • Les
    replied
    Re: Hearth Floor

    Originally posted by james
    You can just fire your oven longer with the standard floor, and you will never completely "fill it up".

    James - isn't there a point where the bricks get saturated? I know I've seen where I slid out a dutch oven that the bricks under it were cooler. It just seems adding a "little" more mass might not be a bad thing. Wasn't someone building their floor with the bricks on edge - be interesting to see his numbers.

    les...

    Leave a comment:


  • james
    replied
    Re: Hearth Floor

    Dmun has it right. We thought about the island hearth as a transition design, back when there was a larger number of folks considering building the Scott oven. I even built an oven with the island hearth myself, but experience has shown that you don't need the "island" mass under a standard 2"-3" cooking cooking floor. More than that, the extra mass can be negative.

    The question is whether a thick floor will give you more retained heat for baking, and in a vast majority of situations, the answer is no. Don't forget that your oven will only retain heat that you put in it in the first place. The longer the fire, the more heat you have to work with - regardless of how thick the floor is. Also remember that in order to fully heat your floor, you would have to heat the entire mass (top to bottom) to 800?F+ -- which is an incredible amount of heat. That is why you don't need to go thicker on the floor. You can just fire your oven longer with the standard floor, and you will never completely "fill it up".

    Hope this helps.
    James

    Leave a comment:


  • MK1
    replied
    Re: Hearth Floor

    dmun,
    The reason I was contemplating hearth mass was because of the quote from Les below. He implies the oven is tuned for pizza over all around baking. I'm very hesitant to change anything in the basic design for the reasons mentioned in my previous post. The only change I have in my build is a copper foil vapor barrier between the dome and it's insulation.
    I know I'm being a PIA but I am compelled to turn this thing over in my mind until I think I understand the thermal dynamics of the oven, always trying to reinvent the wheel.
    I don't want to prototype an oven. I've done that with too many other things and properly done the process involves too much effort, expense and iterations.
    Thanks,
    Mark


    Originally posted by Les
    Mark, if you lay them on edge you are adding mass. That may not be a bad thing. In hind sight (as I am trying to cook coconut shrimp) I would consider a longer heat up time for more retained heat. Baking is becoming the best feature of my oven - we are getting burned out on pizza (you guy's don't know where I live so put out the torches ) My reason for laying them flat - it was in the plans...
    Les...

    Leave a comment:


  • dmun
    replied
    Re: Hearth Floor

    I would be very interested to know how the 3" island hearth performs.
    There were very few of these built, it was a transitional idea, and was soon abandoned. A forum search for "island" didn't return anything, perhaps James has a better memory about this than I do.

    Why do you feel you need more floor mass? Am I missing something?

    Leave a comment:

Working...