Sydney Construction Has Started!!

[Muscats]

Re: Sydney Construction Has Started!!

I ran a tape measure over the dimensions on the weekend and am wondering how my design will be to operate. here are the specs so far.

internal dome 1 meter
internal length to where the door will be 1.15 meters
lenght from back wall to outside of the Flue arch 1.72 meters
Door height 35cm
Door width 54 cm
Flue arch is a 34.5cm

It seems like this is a long way from the flue arch where you stand to the back of the oven?

Wow, excellent work, looks fantastic. Your door is slightly bigger than the recommended but only just. Also your Flue arch is probably a bit longer than most, as most people use a half brick for the door seat rather than a full brick and then end up with two brick length for the Flue arch rather than 2 and half.

Looking great tho, and you are blasting through it. Looking forward to seeing the render go on.

[cobblerdave]

Re: Sydney Construction Has Started!!

Well done mate!!!...... yep love the arch work wish I could lay bricks as good as that


regards cobbler dave brisbane Qld

[JD07]

Re: Sydney Construction Has Started!!

We /Have Chimney!!! Plus the benches are tiled. Hopefully this weekend the insulation blanket and the render will be on and I will be cooking by mid Week!!!!

[JD07]

Re: Sydney Construction Has Started!!

Well brick arches are so much harder to cut than I could have imagined, its taken over a week just for this.




The problem was I decided to make the flue arch out of the same brick as the bas and hence it took days cutting and wreaking bricks to get the final batch and then to put them in place,,,,,,

Anyway just the chimney to go and then I can start on the finishing touches.

I ran a tape measure over the dimensions on the weekend and am wondering how my design will be to operate. here are the specs so far.

internal dome 1 meter
internal length to where the door will be 1.15 meters
lenght from back wall to outside of the Flue arch 1.72 meters
Door height 35cm
Door width 54 cm
Flue arch is a 34.5cm

It seems like this is a long way from the flue arch where you stand to the back of the oven?

[Huhness]

Re: Sydney Construction Has Started!!

Well done that looks like a solid WFO!

[JD07]

Re: Sydney Construction Has Started!!

So I am going to finish of the flue arch and then tile the bench tops this week "hopefully" then I can render the dome so that the render sits on top of the tiles and it will have a nice smooth edge.



Lets see how that goes.

[JD07]

Re: Sydney Construction Has Started!!

[JD07]

Re: Sydney Construction Has Started!!

OK so I was wrong about the cutting, man there was brick dust flying everywhere. I ended up cutting heaps of small pieces to fit gaps I am not sure I should have had.


Here are a couple of photo's of how the work progressed.

[Huhness]

Re: Sydney Construction Has Started!!

WooHoo the dome and door arch are done I will post some photos when I get into work on Monday.

well done!

[JD07]

Re: Sydney Construction Has Started!!

WooHoo the dome and door arch are done I will post some photos when I get into work on Monday.

[JD07]

Re: Sydney Construction Has Started!!

No all the cutting I am going to do is halve each brick. The kit already had the door arch bricks cut with a taper to easily form the arch so I figure the less cutting the better. I am suppsed to have started already but I took my daughter to the coffee shop instead. I will get there eventually.

[Huhness]

Re: Sydney Construction Has Started!!

Hey champ good luck this weekend take loads of pictures. Are you tapering your bricks?

[JD07]

Re: Sydney Construction Has Started!!

Mate yep it's from Feild Furnac they will make up a kit for whatever style oven you want to build. They know what they are doing and are very helpful.

Should have the bricks laid by the end of the weekend.

[Huhness]

Re: Sydney Construction Has Started!!

Wow you're off to a good start!

Whats the kit like? Size, bricks, accessories and cost? I saw they mention a kit on their website but no other information. You have the kit from Field Furnace right?

[JD07]

Re: Sydney Construction Has Started!!

Well the oven arrived last weekend but I didn't get anything done due to the other projects. I am going to cut out my arches this weekend and then its on like donkey kong this weekend.

Just leaving work to by the tiles for the dome and bench tops now.