Announcement

Collapse
No announcement yet.

31"/800mm in Eindhoven, the Netherlands: Design critique and build topic

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Toiletman
    replied
    Two more questions that came up during preparations for the work after:
    • Under which layers should I put the mosaic tiles? as they are there to protect 'wicking' insulation materials from water, I'm assuming they should also be under the fire blankets and possibly also the vermiculite stucco?
    • I did some calculations on the side thrust of the chimney, and were the side walls freestanding, they would definitely topple. However, they're partly embedded in the stucco, and will also be attached to the stone floor (which consists of loose stones basically). I'll probably put in a buttress, as depicted in the picture below, but would welcome any comments/remarks about people's experience with similar arches.
    Ie. with some of the casted chimneys I would imagine that they also take up the side thrust, that might be a solution I could also consider. The buttress I'm currently planning is also only supporting the side walls on the 'back'. I'm assuming that the walls are sufficiently short/stiff that this will basically support the whole sidewall, but also here: any experience/knowledge is welcome!

    Leave a comment:


  • Toiletman
    replied
    Thanks for your comments Giovanni Rossi and UtahBeehiver. Based on your info I also went for the Dremel and homebrew design. I chose the 'life, the universe and everything' theme, which also mixes well with my age, and with a little play, the year of fabrication and the number of our address.

    Probably some final touches to the dome on wednesday: pointing work on the inside, the mandatory pizza oven eats man picture, and probably hand prints on the top. Then it's time for holiday, and when we come back I'll start work on the chimney. Happy with the result of the work so far, and already wondering about lighting it up.... although that's still quite some time away. Thanks for all the priceless advice, tooling, support and information here, making this oven would have otherwise really been impossible.

    Leave a comment:


  • UtahBeehiver
    replied
    I just used my homebrew mortar like GR did as well as a dremel tor the design. He is right, no one but you and the forum will know it is there but then again it is cool to do and you only get a chance one time. That said, I have also seen some nice placks made and place on the outside of the oven.

    Leave a comment:


  • Giovanni Rossi
    replied
    Looking good! you must be getting excited to drop in that keystone!

    My mortar was dark enough to contrast with the lighter brick, so I just used that to fill in the design I carved with a Dremel.

    I had to mortar 2 full bricks together to make my keystone. I used the time while the clamps were on and the mortar was curing to carve and work some mortar into the design. The next morning I double checked that it was holding well. I check it now and again and so far none has landed in a pizza.

    I was inspired by RusselI's (UtahBeehiver ) cool design. I didn't spend a lot of time on mine because the artist in me has yet to emerge.

    Unless you're going to take a pic and display it next to the oven, few are going to see your efforts; but, I admit to enjoying that I know it's there.


    Leave a comment:


  • Toiletman
    replied
    After a week of a lot of bad luck (dead car battery, broken bike gear cable, flat tire) it was finally possible to get some bricks in...

    Two rows of quarter bricks. The issue of them being too wide didn't really lead to any problems... just that I had quite a few too many. The anchor brick for the last row is now in, so hopefully tomorrow I'll finish that and then it's time for the keystone.

    I've seen some really nice designs with prints and engravings on the keystones. I was wondering: what kind of material could I use to color the mortar such that it stays in place and also keeps it contrast?

    Leave a comment:


  • rsandler
    replied
    Originally posted by Toiletman View Post

    Wow, that's pretty quick. I had to gently tap my keystone in place, so I didn't want to risk it. However, I pulled it out today, and indeed quite a bit of mortar leakage. However, one day later it was still easily cleanable so it turned out quite nice. The side supports are a lot worse, I've probably gotta clean them with a power tool... or try to sand them or sth... any tips on cleaning dried up mortar?
    Wire brush and white vinegar worked pretty well for me to clean up excess mortar; for bigger squeezed out bits, just aggressively scraping with a trowel can often do the trick.

    Leave a comment:


  • Toiletman
    replied
    Thanks for your comment UtahBeehiver !

    Latest status update: The halfbrick courses are all in and I've been hard at work cutting the quarter bricks. In doing that I've run into a little issue. Actually I'm not sure if it's really a problem, but I'd at least like to share it such that other people don't make the same mistake.
    As probably everyone has, I've been using the great calculation sheet by deejayoh. While cutting the bricks I assumed that I had to spread the cuts equally across the full brick. However, that's not really the case: the sheet by default calculates the longest side of the cut brick to be a half or quarterbrick size. As a cutting jig I'm using Chipster's design, flipping the brick after each cut. This results in a long and a short side sharing the full length of the brick --> instead of 'two long sides' as the calculator assumes by default.
    This difference is quite small at small angles (lower in the dome), but gets larger and larger the higher up you come. For the half bricks it did not cause any realizable problems, but when cutting the final quarter brick course I was struggling to get the spacing correct, hence I dove in. It now seems that the bricks for course 10 I cut are basically 5mm / 1/8" too long. I've still got to put course 9 in, so I haven't been able to test yet to see if it would really bother me. In the end it would result in more mortar usage, which shouldn't really be a problem. Luckily course 11 hasn't been cut yet, so for that one I can correct.

    Lessons learned:
    • Check the calculator thread more carefully, deejayoh mentions the possibility to adjust the brick width there
    • 'Quarter bricks' are really only 'quarter bricks' for course 9, afterwards they become smaller.
    Find below some pictures of the current status and also illustration of how course 10 and 11 bricks fit inside a full brick.

    Did you guys run into the same issue? Or did you correct for it beforehand in the calculator? I might've just missed this in other posts as the focus while looking through these threads was on understanding the generic concept and creating the cutting jig.
    Last edited by Toiletman; 06-29-2024, 07:56 AM.

    Leave a comment:


  • UtahBeehiver
    replied
    Nice use of laser level. It is common to see the dreaded droop after clearing the inner arch with your dome courses. Looks like you are right on par.

    Leave a comment:


  • Toiletman
    replied
    Another small update: I got the first 'full round' layer in... it's also the penultimate halfbrick layer. One more to go, which is already cut so hopefully I can put it in tomorrow. After weeks of rain, flooding and cold, now we have a heatwave.. so probably working in very small batches and getting things very wet again. After that it's time to modify the IT to fit the small bricks and see how that goes.

    After the large tolerances on the firebricks I was worried about the build going out of whack. Luckily the laser proved that it's worked itself out correctly. there's max 5mm / 1/8" difference in the extremes.

    Leave a comment:


  • Toiletman
    replied
    Originally posted by RandyJ View Post
    Hey Toiletman the dome arch I was not very worried about it falling so I think I mat have only waited 45 minutes to maybe 1.5 hrs. It was not very long at all. I was worried I had a bunch of mortar to clean up so once it was solid enough that it was no longer squishier I pulled the form and cleaned up. I had to pound my key stone into place with a deadblow mallet so I knew everything was tight so just made sure nothing was wiggle and went for it. The front arch I waited a bit longer but a big part of that was waiting for a friend to get there to help me lift the vent into place . I had just done the vent arch and then vent like 2hr later so was probably 3 to 4 hours after I had set the arch in place I pulled the form. It was also a tight fit so I was not worried about it moving. I was more worried I would hit it trying to lift the vent into place and knock something loose. This was my experience your mileage may very. I would say do what is comfortable for you. But is should hold just fine in a few hours. The dome braces the walls for you.

    Randy
    Wow, that's pretty quick. I had to gently tap my keystone in place, so I didn't want to risk it. However, I pulled it out today, and indeed quite a bit of mortar leakage. However, one day later it was still easily cleanable so it turned out quite nice. The side supports are a lot worse, I've probably gotta clean them with a power tool... or try to sand them or sth... any tips on cleaning dried up mortar?

    Leave a comment:


  • RandyJ
    replied
    Hey Toiletman the dome arch I was not very worried about it falling so I think I mat have only waited 45 minutes to maybe 1.5 hrs. It was not very long at all. I was worried I had a bunch of mortar to clean up so once it was solid enough that it was no longer squishier I pulled the form and cleaned up. I had to pound my key stone into place with a deadblow mallet so I knew everything was tight so just made sure nothing was wiggle and went for it. The front arch I waited a bit longer but a big part of that was waiting for a friend to get there to help me lift the vent into place . I had just done the vent arch and then vent like 2hr later so was probably 3 to 4 hours after I had set the arch in place I pulled the form. It was also a tight fit so I was not worried about it moving. I was more worried I would hit it trying to lift the vent into place and knock something loose. This was my experience your mileage may very. I would say do what is comfortable for you. But is should hold just fine in a few hours. The dome braces the walls for you.

    Randy

    Leave a comment:


  • Toiletman
    replied
    Originally posted by RandyJ View Post
    Toiletman I don't know if you want to hear it or not but when I did my arches I went with pretty wet mortar. That way it was easier to get the tight joints. Besides you have the form to hold it in place. Once everything has set then you pull the form and clean up.

    Randy
    You're still going much faster RandyJ but I've finally taken your advice and got the inner arch in today. Went together much better than I expected. How long did you wait to pull the form? I'm assuming at least a day?

    For the rest progress has been pretty OK, although as mentioned: slow. Row 5 is in, 6 is halfway and row 7 is cut. I hope that's going to be the first one to cover the arch fully.

    I've shared pictures below, some general questions:
    • I've been using some old towels/sheets to keep the dome moist, and also to specifically wet stones just before mortaring in new ones. This seems to be working pretty ok, especially as adding water directly to the stones just doesn't work anymore on the higher slopes. Is this a common experience? Any other way's of working to consider?
    • These higher slopes are starting to need stick to support them. It's rather fiddly work and I don't really have the hang of it yet. My sticks are kind of big compared to what I see around here, and they're quite loose... typically with cleaning the excess mortar I tap a few of them over from bumping into them. Is this a common experience? Or do you guys tap them into place or something?
    Thanks again for all the advice and inspiration that you guys are providing, it's really fun to see it coming together more and more, and get first hands experience on the stuff that other people have already ran into.
    Attached Files

    Leave a comment:


  • RandyJ
    replied
    Toiletman I don't know if you want to hear it or not but when I did my arches I went with pretty wet mortar. That way it was easier to get the tight joints. Besides you have the form to hold it in place. Once everything has set then you pull the form and clean up.

    Randy

    Leave a comment:


  • Toiletman
    replied
    Originally posted by Giovanni Rossi View Post
    Toiletman , you may want to try a technique I got from Russell ( UtahBeehiver ). At the end of your work day, mortar a single brick on your next row and allow it to set overnight. Then, you have a solid anchor to work the next brick against when you start your next work session. Since I didn't lay a lot of bricks each day and I needed to brace each brick the higher I went, I took this advice a little further and worked on multiple rows at a time. At one point my dome looked like steps of a pyramid, but I always had a solid section to tap against.
    That was a fantastic tip, thanks! Not so much visible progress here, but a lot of bricks were cut:
    • closing brick course 3 to arch
    • closing brick course 4 to arch
    • 4th course bricks
    • 5th course bricks
    • inner arch bricks
    Besides I followed UtahBeehiver's tip and put in a pyramid of bricks on the 4th and 5th course. The next day it was much better to put in a number of 4th course bricks. This time fully into the mortar: bottom and sides. I do still feel that both the mortar and stones have to be 'too' wet for this to work, but alas, it goes fine and afterwards they seem pretty well stuck too. Hopefully wednesday will offer good weather and I'll be able to put in the 4th and 5th courses, and manage to get the last side-arch stones mortared in. Then the weekend might lead to an attempt at the arch... or at the minimum cut the back of the arch bricks to the correct shape.

    Any tips for the arch? It seems like a very challenging thing to do, especially with thin mortar joints, and the need for it to fit and look visually pleasing.



    Leave a comment:


  • Giovanni Rossi
    replied
    Toiletman , you may want to try a technique I got from Russell ( UtahBeehiver ). At the end of your work day, mortar a single brick on your next row and allow it to set overnight. Then, you have a solid anchor to work the next brick against when you start your next work session. Since I didn't lay a lot of bricks each day and I needed to brace each brick the higher I went, I took this advice a little further and worked on multiple rows at a time. At one point my dome looked like steps of a pyramid, but I always had a solid section to tap against.

    Leave a comment:

Working...
X