If this is your first visit, be sure to
check out the FAQ by clicking the
link above. You may have to register
before you can post: click the register link above to proceed. To start viewing messages,
select the forum that you want to visit from the selection below.
Gudday
It would be a disadvantage in one way it would make the oven harder to dry out should it become damp or during the drying/curing process
Regards dave
Measure twice
Cut once
Fit in position with largest hammer
What's used for the render? That's probably what I'll do as I'll be enclosing mine.
The short answer to that, for me, is stucco. Stucco is used to protect most Igloo style ovens from the weather. If you are building an Enclosure, you probably want need to include that step.
"Enclosure" is the "politcally correct" name for a Dog House style surrounding which hides a prefectly shaped pompeii oven from view .
Seriously though, an enclosure is a very efficient way to protect a pompeii oven from the elements .
Joe Watson " A year from now, you will wish that you had started today" My Build Album / My Build
Gudday
Why the v-Crete . If I built again it would be, dry the dome ,3 in of ceramic then render over that.
that's what i'm thinking about. get extra blanket and skip the v-crete. it's more in material cost, but a lot less time, labor, and potential for mistakes. you'd likely end up w/ better insulation than adding multiple inches of v-crete to boot.
Gulf, you're a riot...and yes, you're right, but I want an enclosure...thank Stonecutter for that as I he's the inspiration for this lol! The others are Ken524 and Dino
Gulf, you're a riot...and yes, you're right, but I want an enclosure...thank Stonecutter for that as I he's the inspiration for this lol! The others are Ken524 and Dino
And that, is what really, counts the most .
Joe Watson " A year from now, you will wish that you had started today" My Build Album / My Build
that's what i'm thinking about. get extra blanket and skip the v-crete. it's more in material cost, but a lot less time, labor, and potential for mistakes. you'd likely end up w/ better insulation than adding multiple inches of v-crete to boot.
-SM-
Gudday
Sometimes we forget about our time and labour . If we were working for someone we would expect a reasonable rate of pay. Yet when we work for ourselves we tend to undervalue our time and labour value.
Regards dave
Measure twice
Cut once
Fit in position with largest hammer
"Enclosure" is the "politcally correct" name for a Dog House style surrounding which hides a prefectly shaped pompeii oven from view .
LOL. My neighbor looked over the fence and asked if I was building a doghouse when I put up my enclosure. Not sure what kind of dog he thought I might have that would need a huge house with a chimney and with a door 4 feet off the ground...
...snip...
i live near enough FB HQ that i can drive there and pick up supplies to save shipping. i'm planning to get the mortar, insulation board and blanket, chimney, from them and source the bricks locally
...snip..
-SM-
Living close enough to FB to drive there, without a doubt the pompeii90 Oven Kit would be the way to go. Then, follow the plans.
Lee B.
DFW area, Texas, USA
If you are thinking about building a brick oven, my advice is Here.
I try to learn from my mistakes, and from yours when you give me a heads up.
Living close enough to FB to drive there, without a doubt the pompeii90 Oven Kit would be the way to go. Then, follow the plans.
yeah, i'm considering it. it's a bit of a premium, but i don't begrudge them the profit. i'm also looking at a full dome kit. i don't mind doing the labor on a full build, but a dome will be higher quality and i could use that time to knock off the french doors for the patio, the new stucco arch for the gate at the side of the house, etc. or to just sit around and enjoy the oven.
Comment