Hello again! Well, I'm sending a photo of my creation. Hoping that it will be a success and I'm so anxious to make pizza, etc. I'm about to cover the insulation, I made the dome with castable cement and fire brick following the ebook available through Forno Bravo. I read so much about people using a layer of vermiculite and then stucco. I have heated the oven several times with increasingly hot fires. I ended up with 2 small hairline cracks toward the back of the dome (outside). Then I put on 3 layers of blanket ceramic insulation. Then chicken wire and will put on 2 layers of stucco with a small escape valve in the back of the dome. Pretty basic! Its a 42 incher with 2 in board insulation below. The chimney is abt 45 in tall, 8 in dia flue liner to get above the cedar pergola. Can I have a decent oven like this? I dont really seem to have room for a layer of vermiculite concrete as is planned. There is not enough of a ledge to support it. Also, is the stucco by itself going to seal moisture out well enough? Ive read about acrylic additives, etc. As you can see, I built opposing counters, its poured cement, exposed aggregate. Did most of it myself. Gas grill on right and fire pit on left along with sink and fridge. Could use some expert last minute help! Thanks!!
Announcement
Collapse
No announcement yet.
Stucco finish, no vermiculite
Collapse
X
-
Re: Stucco finish, no vermiculite
It's looking great to me, I don't quite understand the apprehension of covering the blanket. 3 layers of blanket will serve you well. And whats up with the escape valve? Did you get that idea from this site? Back to point; you live in a harsh environment, if you build a dome you NEED to protect it from the elements. Acrylic stucco is a magical product - I have had no problems.Check out my pictures here:
http://www.fornobravo.com/forum/f8/les-build-4207.html
If at first you don't succeed... Skydiving isn't for you.
-
Re: Stucco finish, no vermiculite
I got the idea from a couple of entries here on the forum in case of escaping moisture or whatever, to prevent a crack in the outer shell. Also, I've got the product purchased already. Regular stucco and a finish coat, from Menards, Can the acrylic stucco go on top of regular base coat?
Comment
-
Re: Stucco finish, no vermiculite
Originally posted by msylt View PostI got the idea from a couple of entries here on the forum in case of escaping moistureCheck out my pictures here:
http://www.fornobravo.com/forum/f8/les-build-4207.html
If at first you don't succeed... Skydiving isn't for you.
Comment
-
Re: Stucco finish, no vermiculite
Next question...would you coat the blanket and chicken wire with regular stucco and finish it with acrylic? Or..., would you just use acrylic? Do i risk cracking the acrylic if the base layer of stucco cracks?? And, Thanks very much for your time Les!!
Comment
-
Re: Stucco finish, no vermiculite
I did put a layer (around 4 inches) of vermiculite over the blanket. The acrylic stucco is pretty pliable - you should be able to just apply it over the wire and blanket. I personally would cover the wire with an inch of mortar for some rigidity, then cover it with the acrylic.
This is about the best link I can find - I put the stucco over this surface, #106
http://www.fornobravo.com/forum/8/le...d-4207-20.htmlCheck out my pictures here:
http://www.fornobravo.com/forum/f8/les-build-4207.html
If at first you don't succeed... Skydiving isn't for you.
Comment
-
Re: Stucco finish, no vermiculite
Originally posted by msylt View PostWhat was your brand of acrylic stucco and store purchased ? Thx!
(the message was to short so I had to add this text to post)Check out my pictures here:
http://www.fornobravo.com/forum/f8/les-build-4207.html
If at first you don't succeed... Skydiving isn't for you.
Comment
-
Re: Stucco finish, no vermiculite
Really nice looking set up you have. the polished countertops are a really nice touch...and pretty much maintenance free.
Dryvit is an excellent brand of EIFS as long as it is installed according to manufacturers application instructions. Been using it on many construction projects for over 38 years. One of their (as well as all EIFS manufacturers) requirements is that you provide a joint sealant at any exposed edges, ie: countertops, flue, etc. Do NOT leave any edge where moisture can migrate into the base layers of their product. EIFS has had a bad wrap in certain climates but almost all failures were due to incorrect application.....ie, not applying the correct joint sealant to the edges. Dryvit has certain brands of joint sealant and types of joint sealant they recommend, depending on what other material you are caulking to, such as metal flue, concrete countertop, masonry, aluminum, etc. I would also suggest you contact their factory technical support to find out what type of acrylic coating they would recommend.
There are many brands of EIFS out on the market which are also excellent products,,,,again, as long as they are installed properly.
good luck,
jonjon
Comment
Comment