Show us your Door Thread
Collapse
X
-
2 PhotosOld World Stone & Garden
Current WFO build - Dry Stone Base & Gothic Vault
When we build, let us think that we build for ever.
John Ruskin -
Re: Show us your Door Thread
Why did you destroy an 18th century home? We are hell bent in the west to preserve them. Buildings from the past are pretty hard to replicate.Check out my pictures here:
http://www.fornobravo.com/forum/f8/les-build-4207.html
If at first you don't succeed... Skydiving isn't for you.Comment
-
Re: Show us your Door Thread
Why did I destroy an 18th century home??? I didn't say destroy, I said dismantle...big difference.
All the floor joists and sills were ruined by dry rot and powder post beetles...they were junk. Almost all of the rafters, roof boards and frame were numbered and sold to someone that re-built it somewhere else. So it was preserved in a way. I saw the home too...the contractor did an awesome job.
I have been around when a few historic homes had to be demolished. Lots of EPA stuff with lead paint and asbestos sometimes prevents saving them...but we were able to salvage some material and hardware before they crunched it up with an excavator. The ring came from a site like that...and I'm glad I have it instead of it being lost forever.Last edited by stonecutter; 07-19-2013, 07:36 PM.Old World Stone & Garden
Current WFO build - Dry Stone Base & Gothic Vault
When we build, let us think that we build for ever.
John Ruskin👍 1Comment
-
Re: Show us your Door Thread
Nice find. Because that ring has only one small contact point with the bolt, it won't get too hot.Kindled with zeal and fired with passion.Comment
-
Re: Show us your Door Thread
Thanks David. The center if the door is a perlcrete slab about 3" thick, and the pin is
only about 2.5" . I think I'm going to use this on my real door, but Ill oil it.Old World Stone & Garden
Current WFO build - Dry Stone Base & Gothic Vault
When we build, let us think that we build for ever.
John RuskinComment
-
Check out my pictures here:
http://www.fornobravo.com/forum/f8/les-build-4207.html
If at first you don't succeed... Skydiving isn't for you.Comment
-
Re: Show us your Door Thread
Gudday Stonecutter
Did you caste the pearlcrete yourself and while I'm asking is it shaped to fit the revel
Regards daveMeasure twice
Cut once
Fit in position with largest hammer
My Build
http://www.fornobravo.com/forum/f51/...ild-14444.html
My Door
http://www.fornobravo.com/forum/f28/...ock-17190.htmlComment
-
Re: Show us your Door Thread
Here's my door. I've come at it from a different angle. I like the traditional look of a wood door. They are cheap and easy to make, relatively light compared to steel and don't conduct like a metal door does.
Mine weighs 2.6 Kgs and is used one handed.
175 x 430 x 19 mm Quilla timber
insulating panel 12 mm bio millboard (no nasty fibres) attached to wood door with 4.5 mm 316 SS bolts.
downside is that the thin insulating panel will start to cook the door if left in place for over 3 hrs at temps above 300 C. This is not a problem because I don't roast or bake for that long or at those temps.3 PhotosLast edited by david s; 07-20-2013, 01:59 PM.Kindled with zeal and fired with passion.👍 1Comment
-
Old World Stone & Garden
Current WFO build - Dry Stone Base & Gothic Vault
When we build, let us think that we build for ever.
John RuskinComment
-
Re: Show us your Door Thread
Yes, it was an experimental panel I made a while back. It fit inside the pattern except two corners, which I trimmed off.Old World Stone & Garden
Current WFO build - Dry Stone Base & Gothic Vault
When we build, let us think that we build for ever.
John RuskinComment
-
Comment
-
Re: Show us your Door Thread
Gudday Tscarborought
A two piece door that's different . Obviously there a reason for that ,is it to do with the entrance hieght?
Regards daveMeasure twice
Cut once
Fit in position with largest hammer
My Build
http://www.fornobravo.com/forum/f51/...ild-14444.html
My Door
http://www.fornobravo.com/forum/f28/...ock-17190.htmlComment
-
-
Re: Show us your Door Thread
Gudday
Ok I give up....why 2 pieces
Regards daveMeasure twice
Cut once
Fit in position with largest hammer
My Build
http://www.fornobravo.com/forum/f51/...ild-14444.html
My Door
http://www.fornobravo.com/forum/f28/...ock-17190.htmlComment





Comment