36" build in Tallahassee - AKA Bruce's Folly

[cobblerdave]

Re: 36" build in Tallahassee - AKA Bruce's Folly

Too bad you aren't closer Dave. I have a pair of Danner quarry gtx boots that need new vibram soles.

Gudday
You make it hard stonecutter ....yes I'd gladly redo your boots but we don't get the American Vibrams in Aust only the European ones....I was thinking on the lines of posting a couple of pics and we get Bruce to do the job
Regards dave

[stonecutter]

Re: 36" build in Tallahassee - AKA Bruce's Folly

Too bad you aren't closer Dave. I have a pair of Danner quarry gtx boots that need new vibram soles.

[Bec1208]

Re: 36" build in Tallahassee - AKA Bruce's Folly

Gudday Bruce
You getting along at a cracking pace now. You would be pleased I'm sure . Really impressed with the trammels , there real inventive. if you ever consider coming out of retirement and need a new career come down under and I'll make a Cobbler out of you!
Regards dave

Not sure I'm ready to quit my lack of a day job. On the other hand visiting the down under would be nice. Bruce

[cobblerdave]

Re: 36" build in Tallahassee - AKA Bruce's Folly

Just to give everyone a laugh, here are Mark 1 and Mark 2 versions of what may or may not resemble a "trammel".

Gudday Bruce
You getting along at a cracking pace now. You would be pleased I'm sure . Really impressed with the trammels , there real inventive. if you ever consider coming out of retirement and need a new career come down under and I'll make a Cobbler out of you!
Regards dave

[Bec1208]

Re: 36" build in Tallahassee - AKA Bruce's Folly

Yes, that looks usable... good job.

Thanks, you really helped me through this. Currently looking at options to create vent to chimney transition. Hope to be able to work it out tomorrow. Bruce

[Bec1208]

Re: 36" build in Tallahassee - AKA Bruce's Folly

I used Selkirk which is like duravent and the anchor plates are similar but not interchangeable. I did anchor the plate to the vent stack then capped my with bricks but I have seen several builds lately with just mounting the plate to the right to the vent stack. You might even consider a clay flue. The duravent or selkirt are really spendy. I am not sure how high you need to go but a clay flue is cheaper and if you do not need to go too high. Mark 1 or Mark 2, if it works, why not.

I want to keep options open, I picked up the adapter plate used for $22 including shipping. My thoughts at the moment are to set up the vent up to the plate. At that point get the dome insulation completed and either stucco or start curing the oven. I think to do this I need to switch from whole bricks to 1" slices to span the upper arch. I can see a couple ways to get through this, suggestions appreciated or I can learn from my own false starts.

[UtahBeehiver]

Re: 36" build in Tallahassee - AKA Bruce's Folly

I used Selkirk which is like duravent and the anchor plates are similar but not interchangeable. I did anchor the plate to the vent stack then capped my with bricks but I have seen several builds lately with just mounting the plate to the right to the vent stack. You might even consider a clay flue. The duravent or selkirt are really spendy. I am not sure how high you need to go but a clay flue is cheaper and if you do not need to go too high. Mark 1 or Mark 2, if it works, why not.

[stonecutter]

Re: 36" build in Tallahassee - AKA Bruce's Folly

Good guesstimate, inner spring line is about 8 1/4". I cut 3 forms but haven't assembled them yet. They have a 14" rise and a 25 inch span. I did a mockup and the pic below is how it ended up. Does it look usable?

Yes, that looks usable... good job.

[stonecutter]

Re: 36" build in Tallahassee - AKA Bruce's Folly

Just to give everyone a laugh, here are Mark 1 and Mark 2 versions of what may or may not resemble a "trammel".

Whatever works....it's the end result that matters most.

[Bec1208]

Re: 36" build in Tallahassee - AKA Bruce's Folly

Bruce,

No moss grows under you. When you decide to go it is 110%. On the home stretch. Great thread to watch.

Russell, I believe you used a duravent flue. I have an 8" adapter plate and need to work out smoke chamber and mounting the plate. Any thoughts on a simple layout (I recall yours as being fairly intricate)? Bruce

[Bec1208]

Re: 36" build in Tallahassee - AKA Bruce's Folly

Bruce,

No moss grows under you. When you decide to go it is 110%. On the home stretch. Great thread to watch.

Thanks Russell, I really got the urge to finish after completing the inner arch. It felt like things were downhill from there. Bruce

Here's looking at you.

[Bec1208]

Re: 36" build in Tallahassee - AKA Bruce's Folly

Just to give everyone a laugh, here are Mark 1 and Mark 2 versions of what may or may not resemble a "trammel".

[UtahBeehiver]

Re: 36" build in Tallahassee - AKA Bruce's Folly

Bruce,

No moss grows under you. When you decide to go it is 110%. On the home stretch. Great thread to watch.

[Bec1208]

Re: 36" build in Tallahassee - AKA Bruce's Folly

bruce, i have been following your build with great interest. i am just starting my build in southern illinois and read your posts almost daily. you have raised lots of good questions i would never have thought of asking. i have learned a lot from you and all the others on this forum.

it won't be long and you'll be cooking five-star restaurant meals in your oven non-stop. it will make the food on your trip out west (which i also followed with great jealousy) seem like run of the mill diner food.
best of luck on your flue and entry.
jon

Thanks for the comments. I read through your current thread, very interesting approach. Look forward to watching as you go along. Pay attention to stonecutter's instructions for designing an arch. Haven't mastered it but I wish I had learned these lessons before the working on the inner arch. Let me know if I can help. Good luck with the build. Bruce

[Bec1208]

Re: 36" build in Tallahassee - AKA Bruce's Folly

The numbers on my diagram are based on a guessimated height of your spring line. You really should measure to get the height...I'm not sure that the span and rise on my drawing will work with what you actually have.

Good guesstimate, inner spring line is about 8 1/4". I cut 3 forms but haven't assembled them yet. They have a 14" rise and a 25 inch span. I did a mockup and the pic below is how it ended up. Does it look usable?