My first attempt for 42" oven / changed to 36"

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • George_M
    Journeyman
    • Oct 2014
    • 290

    #166
    Hi,
    My kitchen design started and together my wood oven!
    Here you can see my kitchen photos and details http://www.fornobravo.com/community/...kitchen-desing

    My wood oven base:
    Last edited by George_M; 03-17-2016, 09:15 AM.

    Comment

    • George_M
      Journeyman
      • Oct 2014
      • 290

      #167
      I have some questions here.
      The base height is 90cm (35.4inch).
      Can i make my perlcrete height 10cm (4inch) ? Or need more??
      I ask because the total height will be: Base+Perlcrete+Floor Plate= 90+10+6=106cm (41inch)
      If i need to double the perlcrete,total height will be 116 cm (45inch).
      Which is the correct height?Also the correct perlcrete size?
      Thanks in advance!

      Comment

      • UtahBeehiver
        Member Moderator
        • May 2012
        • 5262

        #168
        George,

        You have made some major headway will you outdoor kitchen/oven area. I just got back from Athens and from what I saw, roof or inner courtyard areas seem to be the center of family gatherings.

        I assume your p-crete layer will be your insulating section under your oven floor. What ratio of perlite to cement are you considering? The richer the mix the less insulation properties there is. 4" of p-crete (rule of thumb) is roughly equal to 2" of CaSi board and this is the bare minimum thickness under the oven floor. IMHO, if you have the room to make the p-crete thicker then you should. This will help with heat retainage. In talking with our guide in Greece, he mention that wood was very expensive to buy. So you will want to use every bit of BTU you can get.
        Russell
        https://photos.google.com/album/AF1Q...L9lr_UnUgJbF3Z

        Comment

        • George_M
          Journeyman
          • Oct 2014
          • 290

          #169
          Hi,
          You are right my roof will be for gatherings..hehe!

          I think 5:1 perlite/cement ratio is good.But when you say richer mix,for which ratio is rich?
          I can double the perlcrete,but the total cooking floor will go to 116cm (45inch).
          Is it good or is too high?

          As for the woods,i have plenty source of olive tree woods from my olive trees!

          Comment

          • UtahBeehiver
            Member Moderator
            • May 2012
            • 5262

            #170
            Richer would be less perlite, ie 3 to 1 perlite to cement would be richer, so less perlite, less insulation properties. I have seem ratios as high as 8 to 1 but can be a little crumbly. 5 or 6 to 1 is a good balance between insulation and strength, IMHO. Others feel free to chime in.As far as height of the oven floor, there is a general thought of being about elbow height. My thought is a comfortable height where you do not have to stoop a lot to feed the oven with your peel.

            Nice to have a wood supply right in your own back yard.
            Russell
            https://photos.google.com/album/AF1Q...L9lr_UnUgJbF3Z

            Comment

            • George_M
              Journeyman
              • Oct 2014
              • 290

              #171
              I understand it!
              I will go 5:1 ratio.

              As for the height,i will double the perlcrete height or almost double, to have the optimum floor height.

              Another question has to do for the oven opening length.
              Tonyp suggested to me in previous post that i need 20inch length from inner circle floor because i need 3 arcs total.1 for the oven and the other 2 for the chimney
              I saw in many photos from other builders that the length maybe is less than 20inch.


              Can somebody help me on this?
              Thanks
              Last edited by George_M; 03-17-2016, 10:54 PM.

              Comment

              • George_M
                Journeyman
                • Oct 2014
                • 290

                #172
                Hi,
                It is the time to start again the progrees to my wood oven.
                Tomorrow i will make the perlcrete layer.
                I decide to make it 4inch height and 5:1 ratio.
                Click image for larger version

Name:	P_20160614_173959.jpg
Views:	704
Size:	187.6 KB
ID:	389271

                Click image for larger version

Name:	P_20160614_174026.jpg
Views:	644
Size:	179.0 KB
ID:	389272

                You can see the pattern in the photos.
                I draw the final dimension with pencil.
                Perlcrete layer will be until the half brick,is almost the half of the final O.D.
                Entry length is almost 20inch,(2 full bricks)

                I have a question here.
                Perlcrete must be also under the full bricks in the entry?This bricks are for the arcs and chimney.
                Or only need perlcrete to put in the inside of those bricks to the entry?

                Comment

                • Saluki
                  Laborer
                  • Aug 2011
                  • 89

                  #173
                  Get to it! I don't envy that tight corner, that's for sure.

                  Comment

                  • George_M
                    Journeyman
                    • Oct 2014
                    • 290

                    #174
                    Hi,
                    Can you tell me please more details to understand what you mean?
                    Thanks

                    Comment

                    • RandyJ
                      Il Pizzaiolo
                      • May 2010
                      • 1191

                      #175
                      It will be a little tight in the back side there. It is do able just harder than if it was open. Many have been done that way before.

                      Randy

                      Comment

                      • UtahBeehiver
                        Member Moderator
                        • May 2012
                        • 5262

                        #176
                        George,

                        They are saying that your body is going to need to be very flexible or will be by the end of the build since your "working space" on the back side of the oven is limited due to the two walls that are already up. Not impossible just limited.
                        Russell
                        https://photos.google.com/album/AF1Q...L9lr_UnUgJbF3Z

                        Comment

                        • George_M
                          Journeyman
                          • Oct 2014
                          • 290

                          #177
                          I know,but is the only way to build the oven.. I don't have any other space.
                          Thanks Randy

                          Comment

                          • George_M
                            Journeyman
                            • Oct 2014
                            • 290

                            #178
                            Perlcrete layer done!!!
                            Looks perfect!

                            Click image for larger version

Name:	DSC03727.jpg
Views:	573
Size:	288.8 KB
ID:	389373

                            Click image for larger version

Name:	DSC03731.jpg
Views:	612
Size:	338.5 KB
ID:	389369

                            Click image for larger version

Name:	DSC03734.jpg
Views:	577
Size:	399.8 KB
ID:	389370

                            Click image for larger version

Name:	DSC03736.jpg
Views:	543
Size:	414.5 KB
ID:	389371

                            Click image for larger version

Name:	DSC03740.jpg
Views:	627
Size:	502.5 KB
ID:	389372
                            Attached Files

                            Comment

                            • david s
                              Il Pizzaiolo
                              • Mar 2007
                              • 9213

                              #179
                              Originally posted by Saluki
                              Get to it! I don't envy that tight corner, that's for sure.
                              Here's a solution that eliminates the corner altogether and makes it much easier to finish. Just blend the oven into the corner. You go through a lot of vermiculite, but for the large space in the corner at the back you can throw in a lot of empty plastic bottles with the lids on and just cover them with vermicrete.

                              Click image for larger version

Name:	Mark and Jenny Stevens ovenjpg copy.jpg
Views:	714
Size:	462.3 KB
ID:	389375
                              Kindled with zeal and fired with passion.

                              Comment

                              • Saluki
                                Laborer
                                • Aug 2011
                                • 89

                                #180
                                Great suggestion by David. David - did you pour those countertops yourself? Is that crushed glass mixed in?

                                Comment

                                Working...