My first attempt for 42" oven / changed to 36"

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • david s
    Il Pizzaiolo
    • Mar 2007
    • 9213

    #211
    Ah, ok that's good. By the look of the colour I thought it may have been Portland cement and sand only.
    Kindled with zeal and fired with passion.

    Comment

    • George_M
      Journeyman
      • Oct 2014
      • 290

      #212
      Thank you david for your interest!

      Comment

      • George_M
        Journeyman
        • Oct 2014
        • 290

        #213
        I run out from bricks and i will go to buy some and i will buy chimney base.
        How to calculate the correct size so the smoke go inside the chimney and not running out?
        I found this calculator https://community.fornobravo.com/for...lculator/page3
        and i need your help to calculate the correct size.
        My idea is to send the chimney back from the oven with elbow and with a second elbow to go up over the roof.
        Total height from the oven to final height over the roof is 5-6m.

        Comment

        • George_M
          Journeyman
          • Oct 2014
          • 290

          #214
          Any ideas?

          Comment

          • deejayoh
            Il Pizzaiolo
            • Jul 2010
            • 1893

            #215
            For a 36" oven, 6" is standard. But that is for a straight run. With 2 elbows you will slow velocity. I would buy 8" to be safe.
            My build progress
            My WFO Journal on Facebook
            My dome spreadsheet calculator

            Comment

            • david s
              Il Pizzaiolo
              • Mar 2007
              • 9213

              #216
              If your flue is around 5-6 m tall it will more than compensate for the bends IMO. Attached is an oven with such bends and it draws way better than the same oven with a shorter flue of the same diameter.

              Click image for larger version

Name:	Stu and Laras oven.jpg
Views:	581
Size:	1.34 MB
ID:	390394 Click image for larger version

Name:	Matt Theile '09 .jpg
Views:	629
Size:	1.02 MB
ID:	390395
              Attached Files
              Kindled with zeal and fired with passion.

              Comment

              • George_M
                Journeyman
                • Oct 2014
                • 290

                #217
                Ok i will get 8".
                Also,i need to know the chimney opening in the arc before the flue.
                Is it standard dimension?

                David,i plan to do like the oven in your first photo.

                Comment

                • deejayoh
                  Il Pizzaiolo
                  • Jul 2010
                  • 1893

                  #218
                  ah - 5-6 meters height. I didn't see that. At that height, David has a good point - bends are likely a non-issue. I was envisioning something shorter w/ more acute angles to the bends. Six inch is likely fine and will save you a lot of $$$
                  My build progress
                  My WFO Journal on Facebook
                  My dome spreadsheet calculator

                  Comment

                  • George_M
                    Journeyman
                    • Oct 2014
                    • 290

                    #219
                    Progress update!

                    Comment

                    • George_M
                      Journeyman
                      • Oct 2014
                      • 290

                      #220

                      Comment

                      • George_M
                        Journeyman
                        • Oct 2014
                        • 290

                        #221
                        Tomorrow we will make the entrance arch.
                        I think all goes well so far..

                        Comment

                        • George_M
                          Journeyman
                          • Oct 2014
                          • 290

                          #222
                          Hi,
                          I need your help for the first arc.
                          Which size for the bricks is ideal for the first arc?Half or full brick?
                          Any ideas or photos i will appreciate.
                          Thanks

                          Comment

                          • UtahBeehiver
                            Member Moderator
                            • May 2012
                            • 5262

                            #223
                            Tapered inner arch are the easiest to make a dome to arch transition but are more difficult to understand conceptually. Here is a pic (by Mr. Chipster) of one similar to what I think you want and shows how the IT helps make the angles. This require the use of a full brick which is cut down but it is more than a half brick. I think you are using the string method which can work as well.
                            Russell
                            https://photos.google.com/album/AF1Q...L9lr_UnUgJbF3Z

                            Comment

                            • George_M
                              Journeyman
                              • Oct 2014
                              • 290

                              #224
                              I saw this photo again but i want to do like pizza bob's idea.
                              I finished the first arc today and some rows!
                              I am close to finish the dome!!!

                              Comment

                              • George_M
                                Journeyman
                                • Oct 2014
                                • 290

                                #225

                                Comment

                                Working...