Announcement

Collapse
No announcement yet.

dmun's 36" geodesic oven part II

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • RTflorida
    replied
    Re: dmun's 36" geodesic oven part II

    David, FANTASTIC!
    Glad to see that first fire. Its been an inspirational treat following your project all these months. The tower is incredible. I know its been said before, but, your attention to detail, planning, and execution have only been matched by a few (if anyone) on the forum. This is one of those times where it can be said - you COULD give up your day job.

    Great work

    RT

    Leave a comment:


  • james
    replied
    Re: dmun's 36" geodesic oven part II

    David,
    I feel like a happy in-law -- proud to be involved. This is just great. Congratulations on your first fire, and may there be many more fires and great food for years to come.

    Complimenti,
    James

    Leave a comment:


  • maver
    replied
    Re: dmun's 36" geodesic oven part II

    Forno. Bravo!

    Leave a comment:


  • Les
    replied
    Re: dmun's 36" geodesic oven part II

    Very Cool (hot?) David, and you still have a home Fantastic accomplishment!!!

    Les...

    Leave a comment:


  • dmun
    replied
    First fire!

    I tried to embed a youtube video, but it didn't work. Let's try for a clickable link:

    First fire video

    See if that works, and if it doesn't, here's a picture or two:



    Leave a comment:


  • dmun
    replied
    Re: dmun's 36" geodesic oven part II



    More bluestone edging.



    The cavity is stuffed with scrap fiberglass insulation, and covered with flashing, to prepare for casting the concrete slug.



    Tired? You bet.

    Leave a comment:


  • dmun
    replied
    Re: dmun's 36" geodesic oven part II



    This is the flashing at the top of the flue tiles, just wrapped around and bolted, with four tabs to establish the top of the slab. This will let me cast a concrete chimney cap and allow for expansion of the flue tile stack.



    Here are the last two flue tiles in place.

    Almost every chimney, no matter how humble, has some sort of flourish at the top. I think it's a bit of relief that the mason is done with this arduous job.



    This was designed to mirror, in a shallow way, the decorative corbels above the oven opening. Also, there are no exposed cuts to deteriorate in this high wear area.



    Note how the bricks are tilted at a ten degree angle? This establishes the tilt of the bluestone sills used as edging at the top, tilted to repel standing water.

    Leave a comment:


  • dmun
    replied
    Re: dmun's 36" geodesic oven part II

    Finally!



    Above the roofline, and done with blocks, I can use the Bricky again.



    What a difference it makes in the quality of the work.



    And speed. Higher,



    and higher.

    Leave a comment:


  • dmun
    replied
    Re: dmun's 36" geodesic oven part II

    Here's another thing I figured out too late:



    A jig for filling the spaces between the blocks from above. It's two pieces of "L"-shaped quarter-inch luan, screwed to a piece of two-by-four. Fill and tamp, the job's done.



    I start with bricks, to flare out the chimney to it's final size above the flashing. Up to the roof peak.



    Another layer of flue tiles in place.



    Widening layers of brick. Notice the thin strips of plywood: They are space holders for the flashing, so I don't have to angle grind slots in a precarious place.

    Leave a comment:


  • dmun
    replied
    Re: dmun's 36" geodesic oven part II



    Here I am, leaning down to stuff used fiberglass insulation into the block voids, to keep all my mortar from falling down the holes.



    Laying out mortar. You notice that the short piece of the big flue tile was put in down here, to make the two stacks level and even. I wanted full pieces up where the weather exposure is the greatest. I've been looking at a lot of chimneys, and you'd be surprised how many are deteriorating at the top.



    More mortaring,



    and blocks. Note those woven gloves with rough rubber on the palms, I figured out to late that you didn't need to work concrete with bare hands until you bleed.

    Leave a comment:


  • asudavew
    replied
    Re: dmun's 36" geodesic oven part II

    Just awesome.

    What else can I say?

    What are you going to do when you are done?

    Do you have something else to look forward to?

    Leave a comment:


  • dmun
    replied
    Re: dmun's 36" geodesic oven part II

    Now, to above the roof:



    The winch was mounted on the roof sheething, screwed through to the structure underneath.



    It was really high up, and perched on that curved decking was a challenge, especially when it got bits of sand and mortar from the masonry, which made it slippery. A hint: Kitty litter buckets aren't engineered for hoisting masonry. That handle died toot sweet.



    One thing I did was to build a little work platform on the back side of the chimney, I was able to do the heavy work, like lowering flue tiles, from a level perch.



    It did leave me working under grade for the first couple of courses.

    Leave a comment:


  • jwnorris
    replied
    Re: dmun's 36" geodesic oven part II

    Impressive, to say the least.

    J W

    Leave a comment:


  • dmun
    replied
    Re: dmun's 36" geodesic oven part II

    At the tower ceiling,



    The flues converge.



    I couldn't climb the ladder that high, there wasn't room. I had to climb the scaffold and then scoot sideways to get onto the ladder.



    At the top. From here on, it's building from the outside.

    Leave a comment:


  • dmun
    replied
    Re: dmun's 36" geodesic oven part II

    Moving upward:



    A chimney block in position



    Another insblock19 slip plane.



    As I got higher, I built a platform to work on. Notice the household storage bowl at my feet. I ran out of space for the mortar tub, and after it tipped off a precarious perch, i switched to that bowl to carry up the mortar.



    I eventually put a step stool on top of that. In August, window or no window, it was a sweat box in the tower. The air conditioning didn't flow up, of course, and lugging stuff up the ladder into the heat made this one particularly unpleasant job.

    Leave a comment:

Working...
X