Tools, Tips and Techniques - Forno Bravo Forum: The Wood-Fired Oven Community

Forum Notice: The forum has been upgraded and restored to November 2. Posts and new accounts created after November 2 were lost. Sorry for the inconvenience.
If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Topics	Statistics	Last Post
Sticky: Dome spreadsheet calculator by deejayoh Started by deejayoh, 07-26-2012, 02:37 PM	116 responses 50,067 views 3 reactions	Last Post by Tomweb 09-06-2026, 05:40 AM
Sticky: Concrete by the wheelbarrow, mixer, trailer or pump by james Started by james, 12-04-2006, 02:14 PM	67 responses 72,419 views 0 reactions	Last Post by Gulf 03-29-2024, 06:40 PM
Sticky: Hendo's dome gauge -- nice idea by Hendo Started by Hendo, 08-13-2007, 06:08 AM	33 responses 43,617 views 1 reaction	Last Post by mirassou 04-23-2022, 12:43 PM
Sticky: Official - Show off your tools. by V-wiz Started by V-wiz, 03-28-2013, 08:35 PM	99 responses 15,365 views 0 reactions	Last Post by UtahBeehiver 03-23-2020, 05:37 AM
Sticky: Safety Issues by james Started by james, 06-17-2007, 01:56 AM	98 responses 25,584 views 1 reaction	Last Post by Guest 12-11-2014, 03:34 PM
Cleaning Exterior Firebricks by Obese-Wan Kenobi Started by Obese-Wan Kenobi, 02-10-2010, 07:11 PM	0 responses 1,347 views 0 reactions	Last Post by Obese-Wan Kenobi 02-10-2010, 07:11 PM
burning a little wood in a gas or electric oven? by dieter Started by dieter, 02-09-2010, 11:51 PM	0 responses 1,600 views 0 reactions	Last Post by dieter 02-09-2010, 11:51 PM
Using hardibacker as vermicrete form by kebwi Started by kebwi, 02-07-2010, 12:00 AM	4 responses 3,100 views 0 reactions	Last Post by Tscarborough 02-09-2010, 08:52 AM
How to work out arch load bearings. by brickie in oz Started by brickie in oz, 02-08-2010, 07:24 PM	0 responses 2,261 views 0 reactions	Last Post by brickie in oz 02-08-2010, 07:24 PM
Thickness of sheet metal for a door by papavino Started by papavino, 11-02-2009, 09:39 AM	21 responses 8,021 views 0 reactions	Last Post by kebwi 02-08-2010, 12:13 PM
chipped oven floor bricks by andy71180 Started by andy71180, 02-06-2010, 02:43 PM	2 responses 1,859 views 0 reactions	Last Post by nissanneill 02-06-2010, 04:18 PM
Hardibacker vs. Durock...and how to cut by kebwi Started by kebwi, 02-04-2010, 11:23 AM	10 responses 13,538 views 0 reactions	Last Post by fxpose 02-05-2010, 09:22 AM
Pizza Oven on a Trailer by dsclarow Started by dsclarow, 09-28-2008, 05:04 PM	21 responses 19,265 views 0 reactions	Last Post by Guest 02-05-2010, 06:37 AM
How to attach hardibacker to a rebar skeleton by kebwi Started by kebwi, 02-03-2010, 08:27 AM	18 responses 5,146 views 0 reactions	Last Post by kebwi 02-03-2010, 08:32 PM
Quikwall Quikwall Surface Bonding Cement thickness by kebwi Started by kebwi, 02-01-2010, 06:23 AM	9 responses 14,347 views 0 reactions	Last Post by sjmeff 02-03-2010, 10:34 AM
Brick cutting - advice in Australia by Mark CH Started by Mark CH, 02-01-2010, 01:58 PM	10 responses 4,086 views 0 reactions	Last Post by dmun 02-02-2010, 03:28 PM
Concrete Wet Polisher Advice? by B-1Dude Started by B-1Dude, 01-30-2010, 06:07 PM	0 responses 1,833 views 0 reactions	Last Post by B-1Dude 01-30-2010, 06:07 PM
low tech concrete vibrator by christo Started by christo, 08-13-2008, 07:12 AM	9 responses 29,734 views 0 reactions	Last Post by djag12 01-29-2010, 06:34 PM
Minor question about insulation by kebwi Started by kebwi, 01-27-2010, 11:42 PM	2 responses 1,658 views 0 reactions	Last Post by kebwi 01-29-2010, 07:33 AM
Need advice on what is the best method when installing the insulation blanket please? by Wheels1974 Started by Wheels1974, 01-25-2010, 02:32 AM	13 responses 4,432 views 0 reactions	Last Post by Les 01-28-2010, 06:28 PM
Pool Crete by rcolombo Started by rcolombo, 01-25-2010, 09:53 AM	2 responses 2,319 views 0 reactions	Last Post by christo 01-28-2010, 01:28 PM
Fill underside gaps where dome meets arch? by kebwi Started by kebwi, 01-26-2010, 11:50 AM	1 response 2,055 views 0 reactions	Last Post by kebwi 01-26-2010, 01:39 PM
Concern about mold by kebwi Started by kebwi, 01-23-2010, 08:38 AM	3 responses 2,797 views 0 reactions	Last Post by kebwi 01-23-2010, 05:35 PM
old style lime mix instead of refractofy cement by andy71180 Started by andy71180, 01-20-2010, 11:46 AM	5 responses 6,227 views 0 reactions	Last Post by trockyh 01-23-2010, 06:41 AM
Under Construction by grega Started by grega, 01-20-2010, 10:08 AM	0 responses 1,338 views 0 reactions	Last Post by grega 01-20-2010, 10:08 AM

Previous 1 28 35 36 37 38 39 40 41 48 57 template Next

No topics found.

Working...