Corner Build in South East PA

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • UtahBeehiver
    Member Moderator
    • May 2012
    • 5260

    #61
    You may want to experiment with the refractory mortar before you use it on the whole oven. It is an air set but a heat cure. Ovens typically may not get hot enough for a heat cure. You should run these products by the blog before you purchase.
    Russell
    https://photos.google.com/album/AF1Q...L9lr_UnUgJbF3Z

    Comment

    • Chach
      Master Builder
      • Mar 2018
      • 635

      #62
      Originally posted by UtahBeehiver
      You may want to experiment with the refractory mortar before you use it on the whole oven. It is an air set but a heat cure. Ovens typically may not get hot enough for a heat cure. You should run these products by the blog before you purchase.
      I agree with Russell...it gets very exciting to start and when you see a deal I understand the feeling of wanting to jump on it, but you have to make sure the product your buying is going to be right for the application it was intended for. This forum is a great resource for these types of questions don't hold back. My experience with refractory mortars is this I used heat stop 50 on my outdoor fireplace and it worked good but expensive. I used the homebrew for the actual oven and I liked that much better and was very easy to work with. I would use it again if I built another.

      Ricky
      My Build Pictures
      https://onedrive.live.com/?authkey=%...18BD00F374765D

      Comment

      • Chris inPA
        Apprentice
        • Jul 2020
        • 104

        #63
        Question in placement of the inner arch:

        I believe that the outermost edge of the inner arch should touch the edge of the line which indicates the circumference. Is that correct? Or is it the innermost edge that should touch?
        Attached Files
        What comes easy won't last long, and what lasts long won't be easy.

        Comment

        • Chach
          Master Builder
          • Mar 2018
          • 635

          #64
          Here us a picture of where the inside of the arch should be set. The inside of the arch should touch the ovens inside circumference. note my picture looks like the arch is away from the inner circumference but that is because I cut the floor about 1/8"-3/16" shorter for expansion.

          Ricky
          My Build Pictures
          https://onedrive.live.com/?authkey=%...18BD00F374765D

          Comment

          • Chris inPA
            Apprentice
            • Jul 2020
            • 104

            #65
            Chach Perfect. Thank you again. How deep was your inner arch form?
            What comes easy won't last long, and what lasts long won't be easy.

            Comment

            • UtahBeehiver
              Member Moderator
              • May 2012
              • 5260

              #66
              Pic 1 incorrect, pic 2 correct. Be sure leave a release under your arch form, at least 1/2" so you can drop form out without disturbing the arch.
              Chalch's placement of the arch is correct. Your arch template width is fine, you don't want it too wide.
              Russell
              https://photos.google.com/album/AF1Q...L9lr_UnUgJbF3Z

              Comment

              • Chach
                Master Builder
                • Mar 2018
                • 635

                #67
                Originally posted by Chris inPA
                Chach Perfect. Thank you again. How deep was your inner arch form?
                Like 5" or so I think that part doesn't matter as you need it just to hold the brick a little when assembling and putting the arch together it will stick to the brick next and hold it the form is just that to keep the form your shooting for and provide some support. Russell is correct you want to shim that form off the ground so you're not beating the form out. My picture does not show this part as I did not do it until later. Here is my picture showing this.

                Ricky
                My Build Pictures
                https://onedrive.live.com/?authkey=%...18BD00F374765D

                Comment

                • Chris inPA
                  Apprentice
                  • Jul 2020
                  • 104

                  #68
                  I haven't uploaded anything in a while. Today I mixed mortar for bricks for the 1st time. I mortared the 1st course and started cutting the inner arch tapers.
                  Attached Files
                  What comes easy won't last long, and what lasts long won't be easy.

                  Comment

                  • Chris inPA
                    Apprentice
                    • Jul 2020
                    • 104

                    #69
                    I stripped the forms off of the insulating hearth this morning at 7 AM and worked all day.
                    What comes easy won't last long, and what lasts long won't be easy.

                    Comment

                    • Chris inPA
                      Apprentice
                      • Jul 2020
                      • 104

                      #70
                      I put an expansion joint/heat break in the hearth. It's filled with crushed up low density fire bricks and the ends are filled in with Kaowool tape "glued" in with rtv sealant.
                      What comes easy won't last long, and what lasts long won't be easy.

                      Comment

                      • Neil.B
                        Apprentice
                        • Jul 2020
                        • 184

                        #71
                        Great progress, well done.

                        I used a 2" piece of polystyrene for my arch form. As soon as I placed the last brick I took it out to clean up the joints... i don't advise doing this.

                        ​​​​​​​
                        My 32" oven, grill & smoker build https://community.fornobravo.com/for...oven-and-grill

                        Comment

                        • Chris inPA
                          Apprentice
                          • Jul 2020
                          • 104

                          #72
                          This is the last row that the inner arch intersects.
                          Attached Files
                          What comes easy won't last long, and what lasts long won't be easy.

                          Comment

                          • Chris inPA
                            Apprentice
                            • Jul 2020
                            • 104

                            #73
                            More pictures as I haven't posted in a while.
                            Attached Files
                            What comes easy won't last long, and what lasts long won't be easy.

                            Comment

                            • Chris inPA
                              Apprentice
                              • Jul 2020
                              • 104

                              #74
                              More pictures
                              Attached Files
                              What comes easy won't last long, and what lasts long won't be easy.

                              Comment

                              • Chris inPA
                                Apprentice
                                • Jul 2020
                                • 104

                                #75
                                I had a few scraps of laminate flooring from my daughters room. I laid them on the cooking floor to keep it clean. Notice: the seams run parallel to the opening so that I can get it out when I'm done.
                                What comes easy won't last long, and what lasts long won't be easy.

                                Comment

                                Working...