Getting Started

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Topics	Statistics	Last Post
Sticky: FB Brand Insulation by james Started by james, 01-14-2008, 07:36 PM	87 responses 27,590 views 0 likes	Last Post by francisb 04-09-2021, 03:37 PM
Sticky: Hearth Design Philosophy by james Started by james, 06-07-2006, 06:38 PM	51 responses 37,836 views 1 like	Last Post by narcosi 04-21-2020, 03:30 AM
Sticky: High Heat Mortar Primer by james Started by james, 08-22-2006, 12:04 PM	109 responses 48,593 views 0 likes	Last Post by UtahBeehiver 09-21-2018, 07:36 AM
Sticky: Insulation Efficiency by james Started by james, 08-22-2005, 02:03 PM	192 responses 49,591 views 1 like	Last Post by UtahBeehiver 11-20-2017, 07:36 AM
Sticky: Looking for design suggestions by Dave T Started by Dave T, 06-11-2015, 01:52 AM	12 responses 5,028 views 0 likes	Last Post by v12spirit 06-26-2015, 01:17 AM
Sticky: FB Mortar by james Started by james, 11-11-2009, 05:33 PM	15 responses 10,591 views 0 likes	Last Post by TxTanner 07-30-2013, 08:20 PM
Sticky: Measuring your Hearth by james Started by james, 05-30-2006, 04:01 PM	19 responses 19,581 views 0 likes	Last Post by Neil2 10-28-2010, 04:25 PM
Refractory over a barrel mold by buckeyebreadman Started by buckeyebreadman, 03-10-2011, 03:13 PM	9 responses 2,448 views 0 likes	Last Post by buckeyebreadman 03-13-2011, 02:34 PM
morter by jersey Started by jersey, 03-12-2011, 08:04 PM	0 responses 872 views 0 likes	Last Post by jersey 03-12-2011, 08:04 PM
Cooking Floor Height ? by Mark Watkins Started by Mark Watkins, 03-09-2011, 05:20 PM	4 responses 2,644 views 0 likes	Last Post by C5dad 03-10-2011, 10:03 PM
Materials Required by rodeair Started by rodeair, 03-06-2011, 06:58 PM	2 responses 1,051 views 0 likes	Last Post by rodeair 03-06-2011, 07:59 PM
An all-firebrick oven by Brock Started by Brock, 02-10-2011, 09:24 AM	7 responses 1,604 views 0 likes	Last Post by Lburou 03-02-2011, 08:05 PM
Insulating Firebricks by cleverdick Started by cleverdick, 02-27-2011, 04:07 AM	14 responses 2,770 views 0 likes	Last Post by Johnny the oven man 02-28-2011, 02:33 PM
Steel Dome Oven On A Trailer by Grimaldi Started by Grimaldi, 01-19-2009, 01:20 PM	34 responses 8,758 views 0 likes	Last Post by Guest 02-28-2011, 01:44 PM
Fire bricks by cookinghomer Started by cookinghomer, 07-25-2005, 09:57 AM	2 responses 5,541 views 0 likes	Last Post by bullrdrnm 02-25-2011, 12:06 PM
Optimal hearth height by pluscwc Started by pluscwc, 02-18-2011, 10:21 PM	2 responses 2,497 views 0 likes	Last Post by lwood 02-23-2011, 04:58 PM
oven opening size by thezaman Started by thezaman, 02-21-2011, 09:17 AM	5 responses 1,495 views 0 likes	Last Post by thezaman 02-22-2011, 07:49 PM
Can FB Insulation Board Get Wet? by Scott from Alaska Started by Scott from Alaska, 07-23-2010, 08:59 AM	1 response 1,699 views 0 likes	Last Post by neophyteguy 02-21-2011, 07:38 AM
materials by Chris Bowman Started by Chris Bowman, 02-18-2011, 03:16 AM	4 responses 1,068 views 0 likes	Last Post by GianniFocaccia 02-19-2011, 04:09 PM
Alternative bases & foundations by Filthymutt Started by Filthymutt, 02-17-2011, 08:26 AM	9 responses 1,309 views 0 likes	Last Post by Neil2 02-19-2011, 01:55 PM
Building a Pompeii Oven - finally by efleifel Started by efleifel, 07-06-2008, 04:28 PM	91 responses 12,069 views 0 likes	Last Post by efleifel 02-16-2011, 06:25 PM
Flue area to door area question? Confused again by sonomacast Started by sonomacast, 02-06-2011, 04:46 AM	7 responses 1,242 views 0 likes	Last Post by sonomacast 02-16-2011, 01:05 PM
Rectangular Vent gives a Better draw??? by sonomacast Started by sonomacast, 02-10-2011, 12:37 PM	10 responses 2,087 views 0 likes	Last Post by sonomacast 02-16-2011, 01:04 PM
Weatherproof render/stucco by Remember Wingmen? Started by Remember Wingmen?, 12-15-2010, 07:58 AM	3 responses 1,770 views 0 likes	Last Post by Where's Mikes Pizza 02-14-2011, 11:07 PM
Any CAD programs out there for this by Filthymutt Started by Filthymutt, 02-08-2011, 09:04 PM	10 responses 2,230 views 0 likes	Last Post by Filthymutt 02-12-2011, 08:19 PM
Primavera 60 stand installation by RJMang Started by RJMang, 02-12-2011, 06:34 PM	0 responses 1,354 views 0 likes	Last Post by RJMang 02-12-2011, 06:34 PM
Info required in New Zealand by spt Started by spt, 03-12-2009, 05:25 AM	12 responses 3,594 views 0 likes	Last Post by Garth Bostock 02-11-2011, 01:04 PM

Previous 1 18 58 65 66 67 68 69 70 71 78 118 123 template Next

No topics found.

Mark This Channel Read

Working...

Announcement